BCN3D Technologies Sigma(2) Both Extruders 1 0.3 1 0.36 1.1 1 4 0 0.05 2400 0 0.2 0 5 0 0.35 0 0.39 1.1 1 4 0 0.05 2400 0 1 0 5 1 0.2 3 3 3 1 1 0 0 0 0 130 100 0.5 0 0 3 2 3 0.14 100 0.3 0 1 1 2 4 0 0 8 7 1 0 0 2 1 1 30 1 1 Rectilinear Rectilinear 10 20 120 1 1 45,-45 0 45,-45 0 1 20 0 0 1 5 100 1 0.1 0 0 0 3 45 0 1 0 1 0 0 1 0 1 1 1 1 15 20 0 45 100 0 100 1 0 1 0 0 1 0 0 0 -0.5 1 0 210 297 210 0 0 0 -1 -1 -1 1 -1 1 0,0|-40,0|0,0|0,0|0,0|0,0 1 RepRap (Marlin/Repetier/Sprinter) r2 250000 1 M107 ; start with the fan off,G28 X0 Y0 ; move XY to min endstops,G28 Z0 ; move Z to min endstops,T0 ; switch to the 1st extruder,G92 E0 ; zero the extruded length,G1 E10 F100 ; extrude 20mm of feed stock,G92 E0 ; zero the extruded length again, M104 S0 T0 ; left extruder off,M104 S0 T1 ; right extruder off,M140 S0 ; heated bed off,G28 X0 Y0 ; move XY to min endstops,M84 ; steppers off,M107; fan off gcode 1 Funky Town 3000 0.85 0.75 0.8 12000 1200 50 0 1 1 0 0 0 2.6|2.85|2.85|2.85|2.85|2.85 23.95|23.95|23.95|23.95|23.95|23.95 1.25|1.25|1.25|1.25|1.25|1.25 0 0 0 0 0 20 1 0 1 0 0 3 0 1 1 3 9 0 2400 0 2 10 1 100 200 0.2 0 0 0 0 0 0 0 1 0 0 M107 ; start with the fan off,G28 X0 Y0 ; move XY to min endstops,G28 Z0 ; move Z to min endstops,G92 E0 ; zero the extruded length,G1 Z5 F200 ; safety Z axis movement,G1 E7 F50 ; extrude 7mm of feed stock,G92 E0 ; zero the extruded length again,G1 E-4 F200 ; retract before printing 1 1 1 1 1 1 1 0 0 M107 ; start with the fan off,G28 X0 Y0 ; move XY to min endstops,G28 Z0 ; move Z to min endstops,G92 E0 ; zero the extruded length,G1 Z5 F200 ; safety Z axis movement,G1 E7 F50 ; extrude 7mm of feed stock,G92 E0 ; zero the extruded length again,G1 E-4 F200 ; retract before printing 1 0 1 1 1 1 0 0 0 M107 ; start with the fan off,G28 X0 Y0 ; move XY to min endstops,G28 Z0 ; move Z to min endstops,T0 ; switch to the 1st extruder,G92 E0 ; zero the extruded length,G1 E10 F100 ; extrude 20mm of feed stock,G92 E0 ; zero the extruded length again,