Formbot T-Rex 2(3) PLA Medium Right Extruder Only 0 0.8 1 0.96 1 1 1 0 0 1800 0 0.2 0 5 0 0.3 4 8 1 1 2 0 0 0 1 100 95 0.5 0 0 3 2 3 0.14 100 0.3 1 0 1 2 4 0 999 12 7 1 0 999 2 1 1 30 1 0 Fast Honeycomb Rectilinear 0 30 100 0.1 1 0 0 45,-45 0 0 15 1 1 0 3 75 1 0.3 1 0 1 1 45 90,0 0 0 0 0 1 15 20 0 45 100 0 100 1 0 1 0 0 1 0 0 0 0.4 1 0 400 400 400 0 0 0 -1 -1 -1 1 -1 1 0,0|-35,0|0,0|0,0|0,0|0,0 1 RepRap (Marlin/Repetier/Sprinter) r2 115200 1 ; reset BL Touch twice,M280 P0 S160,M280 P0 S160,,; set Acceleration settings,; M204,,; set JERK X/Y to 8s,M205 X10,,; set E-Steps for 3DPW Grey PLA E-Steps test results,M92 E106.6,; save those settings,M500,,; home all axes,G28,,; perform auto leveling,; turned off temporarily for now G29,,; set target temperature and wait (if heating),M109 S230,,; use absolute positioning for the XYZ axes,G90,; move to the Y=20mm position on the bed = FRONT,G1 Y20 F3600,; move to the X=200 mm position on the bed = MIDDLE,G1 X200 F3600,,; purge nozzle,G1 E25 F300 ; turn off extruder LEFT,M104 S0 T0,; turn off extruder RIGHT,M104 S0 T1,,; setup for command,G91,; Lift Z 25mm,G1 Z25 F1200,; close command,G90,,; disable motors,M84,,; STOP & flush Cache we hope,; M999,,;Reset Extruder 0,G92 E0 gcode 0 Star Wars 3600 0.5 0.8 0.8 4800 1002 50 0 1 1 0 0 0 1.75|1.75|1.75|1.75|1.75|1.75 46|46|46|46|46|46 1.25|1.25|1.25|1.25|1.25|1.25 0 0 0 0 0 20 1 0 1 1 0 3 0 1 0 3 12 -0.5 600 0 2 0 1 50 200 0.2 0 0 0.8 1 0.96 1 1 1 0 0 1800 0 0.2 0 5 0 0 0 1 0.4 0 0.4 1 1 1 0 0 1800 0 0.2 0 5 0 0.4 0 0.4 1 1 1 0 0 1800 0 0.2 0 5 1 0 0 0 1 0 0 0 0 0 1 0.4 0 0.4 1 1 1 0 0 1800 0 0.2 0 5 0 0.4 0 0.4 1 1 1 0 0 1800 0 0.2 0 5 1 0 0 0 1 0 0 0 0 0 1 0.4 0 0.4 1 1 1 0 0 1800 0 0.2 0 5 0 0.4 0 0.4 1 1 1 0 0 1800 0 0.2 0 5 1 0 0 0 1 0 0 0 0 0 1 0.4 0 0.4 0.9 1 1 0 0 1800 0 0.2 0 5 0 0.4 0 0.4 1 1 1 0 0 1800 0 0.2 0 5 1 0 0 0 1 0 0 0 0 0 0.3 3 3 1 15 25 0.3 4 8 1 0 15 0.1 4 4 2 30 40 0 0 0 0 0 0 1 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 1 1 0 0 1