# generated by Slic3r 1.1.7 on Fri Jan  2 20:31:19 2015
avoid_crossing_perimeters = 0
bed_size = 300,300
bed_temperature = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 30
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 0
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = G92 E0.0 (Make Sure E is set to 0)\nG1 E-3.0 F700.0 (Suck up plastic)\nM106 (Turn fan on full power)\nM104 S0 (Cool down the extruder)\nM140 S0 (Cool down the heated-build-platform)\nG91 (Use relative coordinates)\nG1 Z3.0 (Move up the nozzle a bit)\nG90 (Switch back to absolute coordinates)\n;(G4 S60 Wait for 60 seconds to let everything cool down a bit)\nG1 Y300 F10000.0 (Move to part removal position)\nM18 (Turn off steppers)\nM107 (Turn off the fan)
external_perimeter_speed = 75%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 30
filament_diameter = 2.8
fill_angle = 0
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 200%
first_layer_height = 110%
first_layer_speed = 30%
first_layer_temperature = 0
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 100
interface_shells = 0
layer_gcode = 
layer_height = 0.3
max_fan_speed = 100
min_fan_speed = 75
min_print_speed = 30
min_skirt_length = 0
notes = .3 layer, .20 infill, 0 degrees, 2P, 3L, .1 retract, modified gcode
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].30.20.2P.3L.1r.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 70
perimeters = 2
post_process = /Users/James/github/local/Slic3r/utils/post-processing/filament-weight.pl
print_center = 150,150
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 45
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 50
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 90
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G90 (Switch to absolute coordinates)\nG21 (Set units to millimeters)\n;(M104 S175 set extrd temp - no wait)\n;(M140 S70 set bed temp - no wait)\nM106 S200 (Turn on the fan to 200)\nG28 X Y Z (home the X and Y and Z axis)\nG1 Z2.0 F1000 (Move up a bit)\nG1 X-9.0 Y150.0 F10000 (Move off the edge of the glass)\nG1 Z0.0 F1000 (Move down and touch the glass to prevent oozing while heating)\n;(M116 Wait for bed and xtrd to heat up apparently does not work)\n;(M109 S195)\n;(M190 S70)\nG1 X-9.0 F10000 (Move to the dump position)\nG92 E0.0 (Make Sure E is set to 0)\nG1 E5.0 F39.0 (Extrude a bit to get everything going)\nG92 E0.0 (Make Sure E is set to 0)\nG1 E-0.1 F700.0 Reverse E for prevent dribbling\nG92 E0.0 (Make Sure E is set to 0)\nG1 X10.0 (Move back over the glass to cut off the extrusion)
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 70
support_material_threshold = 0
temperature = 0
thin_walls = 1
threads = 5
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 70
top_solid_layers = 3
travel_speed = 110
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0