Leapfrog Creatr Dual (modified) PLA + PLA High Both Extruders 0 0.4 0 0.4 1 1 6 0 0.05 3600 1 0.4 0 5 1 0.4 0 0.4 1 1 6 0 0.05 3600 1 0.4 0 5 0 0.1 5 3 2 1 2 0 0 0 0 0 200 100 0.5 0 0 3 3 0.14 85 0 1 0 1 2 4 1 999 12 7 1 0 999 2 1 1 30 1 0 Grid Rectilinear 20 15 100 5 1 45,-45 0 0 0 40 0 0 70 1 0.3 1 1 0 4 45 0 0 0 0 0 0 1 0 0 0 1 0 1 0 0 1 0 1 5 50 0 45 100 1 100 1 0 1 0 0 1 0 0 0 0 1 0 210 297 210 0 0 0 -1 0 -1 1 -1 1 0,0|34,0|0,0|0,0|0,0|0,0 1 RepRap (Marlin/Repetier/Sprinter) r2 250000 1 G28 ; home all axes,,T1 ;switch to the 2nd Extruder,G92 E0 ;zero the extruded length,G1 F200 E13 ;extrude 13mm of feed stock,G92 E0 ;zero the extruded length again,G1 E-15 F3000 ;retraction before toochange,,T0,G92 E0 ;zero the extruded length,G1 F200 E13 ;extrude 13mm of feed stock,G92 E0 ;zero the extruded length again,,;Put printing message on LCD screen,M117 Printing...,, ; Retraction Script ; Tool Change Script M104 S0 ; turn off extruder,M140 S0 ; turn off bed,M84 ; disable motors,G91 ;relative positioning,G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure,G1 Z+0.5 E-5 X-20 Y-20 F12000 ;move Z up a bit and retract filament even more,G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way,G90 ;absolute positioning 0 0 Star Wars 0 3000 1 1.2 1 12000 1002 50 0 1.1 0.9 2.85 46 1.25 0 0 0 0 0 20 1 0 0 0 0 1 1 1 1 5 30 0 3000 1 30 0 0.3 3 3 1 15 25 0.2 5 3 1 20 30 0.1 5 3 1 20 40 0 0 0 0 0 1 0 0 G28 F1200 ; home all axes,T0 ; switch to right extruder,G1 Z0.2 ; raise nozzle,G92 E0 ; zero extruder,G1 E3 F225 ; purge nozzle,G1 Y15 Z0.05 F1200 ; slow wipe,G1 Y20 Z0.25 ; lift,G92 E0 ; zero extruder again 1 1 1 1 1 1 0 0 G28 F1200 ; home all axes,T1 ; switch to left extruder,G1 Z0.2 ; raise nozzle,G92 E0 ; zero extruder,G1 E3 F225 ; purge nozzle,G1 Y15 Z0.05 F1200 ; slow wipe,G1 Y20 Z0.25 ; lift,G92 E0 ; zero extruder again 0 0 0 0 0 1 1 0 G28 ; home all axes,,T1 ;switch to the 2nd Extruder,G92 E0 ;zero the extruded length,G1 F200 E13 ;extrude 13mm of feed stock,G92 E0 ;zero the extruded length again,G1 E-15 F3000 ;retraction before toochange,,T0,G92 E0 ;zero the extruded length,G1 F200 E13 ;extrude 13mm of feed stock,G92 E0 ;zero the extruded length again,,;Put printing message on LCD screen,M117 Printing...,, 1 0.4 0 0.4 1 1 6 0 0.05 3600 1 0.4 0 5 0 0.4 0 0.4 1 1 6 0 0.05 3600 1 0.4 0 5 1 0 0 0 1 0 0 0 0 0