PLA High 0 0.4 1 0.48 0.9 1 2 0 0 1600 0 0.2 0 5 0 0.1 4 4 2 1 2 0 0 0 0 90 125 0.3 0 0 3 2 3 0.14 100 0.3 1 0 2 2 4 0 999 12 7 1 0 999 2 1 1 30 1 0 Fast Honeycomb Rectilinear 30 30 100 0 1 0 0 45,-45 1 0 40 0 0 0 0 70 1 0.3 1 1 1 4 45 0 0 0 0 0 0 0 1 15 20 0 45 100 0 100 1 0 1 1 0 1 0 0 0 0 1 0 140 140 140 70 70 0 1 1 -1 1 -1 1 0,0|0,0|0,0|0,0|0,0|0,0 1 FlashForge Dreamer Firmware r2 115200 1 M146 r255 g0 b0 ; Set lights to red while preheating,M907 X100 Y100 Z40 A100 B100 ; Set motor current,M132 X Y Z A B ; Recall home offsets,G28 ; Home axes,G1 Z100 F3300 ; Lower Z,G1 X-70 Y-70 F6000 ; Move to wait position,M7 ; Wait for bed to stabilize,M6 T0 ; Wait for right extruder to reach target temp,G1 X-70 Y-70 F9000 ; Move to front left corner of bed,G1 Z0.3 F6000 ; Move down to purge,G92 E0 ; Zero extruders,G1 X50 Y-70 E20 F2000 ; Extrude a line of filament across the front edge of the bed,G1 X60 Y-70 F180 ; Wait for ooze,G1 X70 Y-70 F5000 ; Fast wipe,G1 Z1 F100 ; Lift,G92 E0 ; Zero extruders again,M146 r255 g255 b255 ; Turn lights on for print,G1 Z0.5 F3300 ; Position nozzle M104 S0 T0 ; cool down extruder,G1 Z140 F3300 ; send Z axis to bottom of machine,M107 ; disable cooling fan,G28 X0 Y0 ; home XY axes,M146 r0 g0 b0 ; Turn lights off,M18 ; disable stepper gcode 0 Take On Me 3600 0.5 0.8 0.8 4200 1200 50 0 1 1 0 0 0 1.75|1.75|1.75|1.75|1.75|1.75 46|46|46|46|46|46 1.25|1.25|1.25|1.25|1.25|1.25 0 0 0 0 0 20 1 0 1 1 0 3 0 1 0 3 12 -0.5 600 0 2 10 1 50 200 0.2 0 0 0.4 1 0.48 0.9 1 2 0 0 1600 0 0.2 0 5 0 0 0 0 0 0 0.4 0 0.4 1.0 1 1 0 0 1200 0 0.2 0 5 0 0 0 0 0 0 0.4 0 0.4 1 1 1 0 0 1200 0 0.2 0 5 0 0 0 0 0 0 0.4 0 0.4 1 1 1 0 0 1200 0 0.2 0 5 0 0 0 0 0 0.3 3 3 1 15 25 0.2 3 3 1 20 30 0.1 4 4 2 30 40