0 0.4 1 0.48 0.95 1 5 0 0 1500 0 1 0 3 0 0.2 4 3 3 1 3 0 200 0 0 100 120 0.3 0 0 3 2 3 0.14 100 0.3 1 0 1 2 2 0 999 18 0 1 0 999 2 1 1 30 1 0 Rectilinear Rectilinear 15 25 125 3 1 45,-45 0 45,-45 0 0 30 0.6 0 0 0 70 1 0.4 1 1 0 4 45 0 0 0 0 0 1 1 1 0 0 1 1 1 5 20 1 45 100 1 100 1 0 1 0 0 1 0 0 0 0 1 0 190 200 190 0 0 0 -1 1 1 1 -1 1 0,0|0,0|0,0|0,0|0,0|0,0 0 RepRap (Marlin/Repetier/Sprinter) r2 115200 0 G28 ; home all axes,G1 X20 Y10 F3000 ; bring extruder to front,G92 E0 ; zero the extruded length,G1 Z10 ; lower,G1 E19 F200 ; purge nozzle quickly,G1 E26 F60 ; purge nozzle slowly,G92 E0 ; zero the extruded length again,G1 E-5.5 F400 ; retract,G1 X190 Z0 F9000 ; pull away filament,G1 X210 F9000 ; wipe,G1 Y20 F9000 ; wipe,G1 E0 ; feed filament back {IF NEWTOOL=0} G1 Z[next_position_z] F1002,{IF NEWTOOL=0} G1 X[next_position_x] Y[next_position_y] F[travel_speed] ; move to next printing location,{IF OLDTOOL=1} G1 E0 F10000; avoid hairs,{IF OLDTOOL=1} G1 E-250 F10000; retract filament,{IF NEWTOOL=0} T0 ;Start tool switch 0,{IF NEWTOOL=0} G1 E0 F[toolchange_retract_speed] ; prime new tool,,{IF NEWTOOL=1} G1 Z[next_position_z] F1002,{IF NEWTOOL=1} G1 X[next_position_x] Y[next_position_y] F[travel_speed] ; move to next printing location,{IF OLDTOOL=0} G1 E0 F10000; avoid hairs,{IF OLDTOOL=0} G1 E-250 F10000; retract filament,{IF NEWTOOL=1} T1 ;Start tool switch 1,{IF NEWTOOL=1} G1 E0 F[toolchange_retract_speed] ; prime new tool,,G92 E0 M104 S0 ; turn off extruder,M140 S0 ; turn off bed,G28 X0 Y0,G1 Z180,M84 ; disable motors gcode 0 Random Song 3600 0.5 0.6 1 9000 1002 5 3 1 1 0 0 0 1.75|1.75|1.75|1.75|1.75|1.75 20|46|46|46|46|46 1.25|1.25|1.25|1.25|1.25|1.25 0 54.7 0 1.76 0 20 1 0 1 0 1 0.02 1 0 0 3 5 -0.5 1200 1 1 30 1 50 200 0.2 0