ABS/HIPS Medium 0 0.4 0 0.4 1 1 1 0 0 1200 0 0.2 0 5 1 0.4 0 0.4 1 1 1 0 0 1200 0 0.2 0 5 0 0.2 3 3 3 1 2 0 0 300 0 0 0.9 0.5 1 2 2.8 0.2 50 0 1 1 2 4 0 Rectilinear 10 20 5 1 0 45,-45 1 0 40 0 1 0.35 1 1 4 30 0 0 0 0 0 1 1 0 0 0 1 0 1 0 0 1 0 1 15 20 0 45 100 1 100 1 0 1 0 1 0 0 1 0 0 0 1 0 230 150 140 115 75 0 1 1 -1 1 -1 1 ; ; **** FlashForge Dreamer Dual Extrusion start.gcode for ABS/HIPS **** ; M146 r255 g255 b0 ; Set the LED lights to YELOW to indicate that we are starting the start.code. M140 S[bed0_temperature] ; Set the heated build plate (HBP) temperature M104 S[extruder0_temperature] T0 ; Set the right extruder temperature M104 S[extruder1_temperature] T1 ; Set the left extruder temperature G90 ; Use Absolute Positioning (make sure to also use this in Simplify3D's settings) G28 ; Move the head to all X/Y/Z end stop positions M132 X Y Z A B ; Recall stored home offsets for XYZAB axis G1 Z100 F3300 ; Move Z to 100 and set feed rate to 3300 mm/min G1 X-110.5 Y-74 F6000 ; Move X/Y to -110.5 and -74. Set feed rate to 6000 mm/min. M7 ; Coolant A on. It's unknown what the Dreamer uses this for. M146 r255 g0 b0 ; Set the LED lights to RED while things heat up. M6 T0 ; wait for toolhead 0 and HBP to reach their temperatures M6 T1 ; wait for toolhead 1 and HBP to reach their temperatures M146 r0 g255 b0 ; Set the LED lights to GREEN to show that the heaters are ready. ; *** STEPPER MOTOR POWER CONTROL *** ; For the following G-code M907: ; 100 = full power. ; X/Y/Z sets the power for the X/Y/Z axis motors. Dreamer uses 100/100/40 for X/Y/Z. ; A sets the power for the right extruder's stepper motor. ; B sets the power for the left extruder's stepper motor. ; Lower values for A/B prevent grinding of the filament and encourage skipping. ; For strong ABS/HIPS filament the Dreamer uses 100 for A or B when used. ; For weaker PLA filament the Dreamer uses 80 for A or B when used. ; This helps prevent the motor from grinding and breaking PLA if the filament is stuck. ; For no filament the Dreamer uses 20 (but never 0) for A or B. M907 X100 Y100 Z40 A100 B100 ; Set the corresponding stepper motor's power level (100=full power) G1 Z0.6 F3300 ; Move Z to 0.6 with a feed rate to 3300 mm/min G4 P2000 ; Wait for 2000 milliseconds M108 T0 ; Select tool head 0 (We always default to tool head 0) M146 r255 g255 b255 ; Set the LED lights to WHITE to indicate that we are ready to print. ; ; **** end of start.gcode **** ; ; ; **** FlashForge Dreamer layer.gcode **** ; ; **** NOW FLASH THE LIGHTS CYAN TO SHOW WE ARE AT A NEW LAYER **** ; M146 r0 g255 b255 ; Set the LED lights to CYAN G4 P50 ; Wait for 100 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P50 ; Wait for 100 milliseconds M146 r255 g255 b255 ; Set the LED lights to WHITE to show that we are printing a new layer ; ; **** end of layer.gcode **** ; ; ; **** FlashForge Dreamer end.gcode **** ; M107 ; Turn the fan off M104 S0 T0 ; Cool down the right extruder M104 S0 T1 ; Cool down the left extruder M140 S0 ; Cool down the HBP G1 Z140 F3300 ; Send Z axis to the bottom of the machine (moves the build plate all the way down) G28 X0 Y0 ; Home X/Y axis only M132 X Y Z A B ; Recall home offsets G91 ; Set to Relative Positioning M18 ; Disable all stepper motors ; ; **** NOW FLASH THE LIGHTS TO SHOW WE ARE DONE **** ; M146 r255 g0 b0 ; Set the LED lights to RED G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds M146 r0 g255 b0 ; Set the LED lights to GREEN G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds M146 r0 g0 b255 ; Set the LED lights to BLUE G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds ; M146 r255 g0 b0 ; Set the LED lights to RED G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds M146 r0 g255 b0 ; Set the LED lights to GREEN G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds M146 r0 g0 b255 ; Set the LED lights to BLUE G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds ; M146 r255 g0 b0 ; Set the LED lights to RED G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds M146 r0 g255 b0 ; Set the LED lights to GREEN G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds M146 r0 g0 b255 ; Set the LED lights to BLUE G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds ; M146 r255 g0 b0 ; Set the LED lights to RED G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds M146 r0 g255 b0 ; Set the LED lights to GREEN G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds M146 r0 g0 b255 ; Set the LED lights to BLUE G4 P1000 ; Wait for 1000 milliseconds M146 r0 g0 b0 ; Set the LED to BLACK G4 P200 ; Wait for 200 milliseconds ; M146 r255 g255 b255 ; Set the LED lights to WHITE to show that we new printing the next layer ; ; **** end of end.gcode **** ; 0 0 Random Song 5400 0.5 0.8 4200 1200 50 1 0.8 1.75 46 0 0 0 0 0 0.3 0 20 1 0 0 1 0 3 0 100 1 220 0 0.9 ; ; **** FlashForge Dreamer Dual Extrusion start.gcode for PLA **** ; M146 r255 g255 b0 ; Set the LED lights to YELOW to indicate that we are starting the start.code. M140 S[bed0_temperature] ; Set the heated build plate (HBP) temperature M104 S[extruder0_temperature] T0 ; Set the right extruder temperature M104 S[extruder1_temperature] T1 ; Set the left extruder temperature G90 ; Use Absolute Positioning (make sure to also use this in Simplify3D's settings) G28 ; Move the head to all X/Y/Z end stop positions M132 X Y Z A B ; Recall stored home offsets for XYZAB axis G1 Z100 F3300 ; Move Z to 100 and set feed rate to 3300 mm/min G1 X-110.5 Y-74 F6000 ; Move X/Y to -110.5 and -74. Set feed rate to 6000 mm/min. M7 ; Coolant A on. It's unknown what the Dreamer uses this for. M146 r255 g0 b0 ; Set the LED lights to RED while things heat up. M6 T0 ; wait for toolhead 0 and HBP to reach their temperatures M6 T1 ; wait for toolhead 1 and HBP to reach their temperatures M146 r0 g255 b0 ; Set the LED lights to GREEN to show that the heaters are ready. ; *** STEPPER MOTOR POWER CONTROL *** ; For the following G-code M907: ; 100 = full power. ; X/Y/Z sets the power for the X/Y/Z axis motors. Dreamer uses 100/100/40 for X/Y/Z. ; A sets the power for the right extruder's stepper motor. ; B sets the power for the left extruder's stepper motor. ; Lower values for A/B prevent grinding of the filament and encourage skipping. ; For strong ABS/HIPS filament the Dreamer uses 100 for A or B when used. ; For weaker PLA filament the Dreamer uses 80 for A or B when used. ; This helps prevent the motor from grinding and breaking PLA if the filament is stuck. ; For no filament the Dreamer uses 20 (but never 0) for A or B. M907 X100 Y100 Z40 A80 B80 ; Set the corresponding stepper motor's power level (100=full power) G1 Z0.6 F3300 ; Move Z to 0.6 with a feed rate to 3300 mm/min G4 P2000 ; Wait for 2000 milliseconds M108 T0 ; Select tool head 0 (We always default to tool head 0) M146 r255 g255 b255 ; Set the LED lights to WHITE to indicate that we are ready to print. ; ; **** end of start.gcode **** ; 230 105 1.0 ; ; **** FlashForge Dreamer Dual Extrusion start.gcode for ABS/HIPS **** ; M146 r255 g255 b0 ; Set the LED lights to YELOW to indicate that we are starting the start.code. M140 S[bed0_temperature] ; Set the heated build plate (HBP) temperature M104 S[extruder0_temperature] T0 ; Set the right extruder temperature M104 S[extruder1_temperature] T1 ; Set the left extruder temperature G90 ; Use Absolute Positioning (make sure to also use this in Simplify3D's settings) G28 ; Move the head to all X/Y/Z end stop positions M132 X Y Z A B ; Recall stored home offsets for XYZAB axis G1 Z100 F3300 ; Move Z to 100 and set feed rate to 3300 mm/min G1 X-110.5 Y-74 F6000 ; Move X/Y to -110.5 and -74. Set feed rate to 6000 mm/min. M7 ; Coolant A on. It's unknown what the Dreamer uses this for. M146 r255 g0 b0 ; Set the LED lights to RED while things heat up. M6 T0 ; wait for toolhead 0 and HBP to reach their temperatures M6 T1 ; wait for toolhead 1 and HBP to reach their temperatures M146 r0 g255 b0 ; Set the LED lights to GREEN to show that the heaters are ready. ; *** STEPPER MOTOR POWER CONTROL *** ; For the following G-code M907: ; 100 = full power. ; X/Y/Z sets the power for the X/Y/Z axis motors. Dreamer uses 100/100/40 for X/Y/Z. ; A sets the power for the right extruder's stepper motor. ; B sets the power for the left extruder's stepper motor. ; Lower values for A/B prevent grinding of the filament and encourage skipping. ; For strong ABS/HIPS filament the Dreamer uses 100 for A or B when used. ; For weaker PLA filament the Dreamer uses 80 for A or B when used. ; This helps prevent the motor from grinding and breaking PLA if the filament is stuck. ; For no filament the Dreamer uses 20 (but never 0) for A or B. M907 X100 Y100 Z40 A100 B100 ; Set the corresponding stepper motor's power level (100=full power) G1 Z0.6 F3300 ; Move Z to 0.6 with a feed rate to 3300 mm/min G4 P2000 ; Wait for 2000 milliseconds M108 T0 ; Select tool head 0 (We always default to tool head 0) M146 r255 g255 b255 ; Set the LED lights to WHITE to indicate that we are ready to print. ; ; **** end of start.gcode **** ; 0.3 3 3 1 15 25 0.2 3 3 1 20 30 0.1 4 4 2 30 40