Default (modified) PLA High 0 0.4 1 0.48 1 1 5 0 0 1500 1 1 1 5 0 0.1 4 4 2 1 2 0 0 0 0 150 105 0.3 0 0 3 2 3 0.2 100 0.3 1 0 2 3 5 0 999 2 7 1 0 999 2 1 1 30 1 0 Fast Honeycomb Rectilinear 20 25 100 5 1 0 0 45,-45 1 0 40 0 0 0 0 20 2 0.4 1 0 1 4 45 0 0 0 0 0 1 1 1 0 0 0 0 1 15 20 1 15 100 1 100 1 0 1 0 0 1 0 0 0 0 1 0 200 200 200 0 0 0 -1 -1 -1 1 -1 1 0,0|0,0|0,0|0,0|0,0|0,0 1 RepRap (Marlin/Repetier/Sprinter) r2 115200 0 T0,M104 S0 ;cancel S3D set temp,G21 ; set units to mm,G90 ; use absolute coordinates,T0 ; select tool 0,G92 E0.0 ; reset e count,M220 S100 ; reset speed multiplier,M140 S[bed1_temperature] ; set bed temperature and do not wait,G28 ; home all axes,G1 X10 Y10 Z10 F4000,M190 S[bed1_temperature] ; set bed temperature and wait,M109 S[extruder0_temperature] ; set print head temperature and wait,G29 ; auto level,; === pause for heating ===,G1 Z10.0 F900 ; move up,G1 E30.0 F500 ; prime extruder,G1 Y15 F9000 ; move back,G1 Z0.2 F1000 ; move down to begin wipe,G1 X110 E4.0 F10000 ; wipe print head (extrude material while we do this),G92 E0.0 ; reset e count G91 ;relative positioning,G1 E-5.00 F1000 ;retract 5mm of filament,G1 Z+1.00 X-20.0 Y+10.0 F20000 ;short quick move to disengage from print,G90 ;absolute positioning,G1 X0.0 Y345.0 F9000 ; move head to back left corner,G91 ; relative positioning,G1 E-5.00 F500 ;retract additional filament to prevent oozing,G90 ;absolute positioning,M104 S0 ;turn off hotend,M140 S0 ;turn off heatbed,G1 Z315 F1000 ;move print bed down to idle position,M106 S0 ; shut off blower,M84 ;motors off,M561 ;clear bed probe transformation gcode 0 Random Song 3000 0.8 0.85 0.9 7800 1020 50 0.2 0.8 0.3 0 0 0 1.72|1.72|1.72|1.72|1.72|1.72 28.25|28.25|28.25|28.25|28.25|28.25 1.31|1.31|1.31|1.31|1.31|1.31 0 0 0 0 0 20 1 0 1 0 0 2 1 1 1 5 12 -0.5 600 0 2 10 1 50 200 0.2 0 0 0 0 0 1 1 1 0 0 0 1 225 100 1 195 80 1 220 80 1 0.3 3 3 1 15 25 0.2 5 3 1 15 20 0.1 4 4 2 20 40