F400_PLA Standard 0 0.4 0 0.45 1 1 4.25 0.05 0 24000 0 0.5 0 5 0 0.2 3 3 2 0 3 0 360 0 0 100 100 0.4 0 0 2 0 4 0.15 100 0.3 1 0 1 1 5 0 999 12 7 1 0 999 2 1 1 30 1 0 Rectilinear Rectilinear 30 20 100 5 1 45,-45 0 45,-45 1 0 30 0.5 0 0 0 70 1 0.35 1 1 0 2 45 45 0 0 0 0 0 2 1 0 0 0 0 1 5 30 1 13 100 1 100 1 1 1 0 0 1 0 0 0 0 1 0 355 355 315 0 0 0 1 -1 1 1 -1 1 0,0|0,0|0,0|0,0|0,0|0,0 1 RepRap (Marlin/Repetier/Sprinter) r2 115200 0 M104 S0 ;cancel S3D set temp,G21 ; set units to mm,G90 ; use absolute coordinates,T0 ; select tool 0,G92 E0.0 ; reset e count,M220 S100 ; reset speed multiplier,M140 S[bed2_temperature] ; set bed temp and do not wait,G32 ; probe bed,M190 S[bed2_temperature] ; set bed temperature and wait,M109 S[extruder0_temperature] ; set print head temperature and wait,; === pause for heating ===,; reset filament monitor,M42 P63 S0,G4 P100,G4 P50,M42 P63 S1,;,G1 Z10.0 F2000 ; move up,G1 E30.0 F500 ; prime extruder,G1 X20 Y15 F9000 ; move back,G1 Z0 F1000 ; move down to begin wipe,G1 X150 E4.0 F10000 ; wipe print head (extrude material while we do this),G92 E0.0 ; reset e count G91 ;relative positioning,G1 E-5.00 F1000 ;retract 5mm of filament,G1 Z+1.00 X-20.0 Y+20.0 F10000 ;short quick move to disengage from print,G90 ;absolute positioning,G1 X0.0 Y350.0 F9000 ; move head to back left corner,G91 ; relative positioning,G1 E-5.00 F500 ;retract additional filament to prevent oozing,G90 ;absolute positioning,M104 S0 ;turn off hotend,M140 S0 ;turn off heatbed,; Reset filament monitor,M42 P63 S0,G4 P100,G4 P50,M42 P63 S1,;,G1 Z315 F1000 ;move print bed down to idle position,M106 S0 ; shut off blower,M84 ;motors off,M561 ;clear bed probe transformation gcode 0 Random Song 6000 0.6 0.7 1 21000 10000 50 0.5 1 0.6 0 0 0 1.71|1.71|1.71|1.71|1.71|1.71 46|46|46|46|46|46 1.25|1.25|1.25|1.25|1.25|1.25 0 13 0 13 0 20 1 0 1 0 0 1 0 1 0 3 0 0 360 1 1 50 1 50 200 0.2 0 0.2 3 3 30 0 0.4 0 0.45 1 1 4.25 0.05 0 24000 0 0.5 0 5 0 0 0 0 0 6000 30 100 0.3 3 3 15 0 0.4 0 0.45 1 1 5.0 0.05 0.15 24000 0 0.5 0 5 0 0 0 0 0 7600 25 100 0.1 4 4 60 0 0.4 0 0.4 1 1 2.5 0.05 0 3000 0 0.5 0 5 0 0 0 0 0 2500 40 250