Creality CR-10(2) PLA Regular 0 0.4 1 0.48 0.97 1 4.9 0 0.4 3300 0 0.2 1 4 0 0.16 6 3 3 1 3 0 0 0 0 120 120 0.5 0 0 3 1 3 0.14 100 0.3 1 0 2 4 4 0 999 12 7 1 0 999 2 1 1 30 1 0 Rectilinear Rectilinear 100 15 130 5 1 45,-45 0 45,-45 0 0 30 0.6 3 0 3 85 1 0.4 1 1 1 1 55 0 0 0 1 0 1 1 1 1 15 20 0 45 100 1 100 1 0 1 0 0 1 0 0 0 -0.2 1 0 235 235 250 0 0 0 -1 -1 -1 1 -1 1 0,0|0,0|0,0|0,0|0,0|0,0 1 RepRap (Marlin/Repetier/Sprinter) r2 115200 1 G28 ; home all axes,M117 Purge extruder,G92 E0 ; reset extruder,G1 Z1.0 F3000 ; move z up little to prevent scratching of surface,G1 X0.1 Y20 Z0.3 F5000.0 ; move to start-line position,G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; draw 1st line,G1 X0.4 Y200.0 Z0.3 F5000.0 ; move to side a little,G1 X0.4 Y20 Z0.3 F1500.0 E30 ; draw 2nd line,; G1 E27 F3000 ; retract filament 3mm,G92 E0 ; reset extruder,; done purging extruder,M92 E118 ;,G1 Z1.0 F3000 ; move z up little to prevent scratching of surface,M117 Filament Frenzy M104 S0; turn off extruder,M140 S0 ; turn off bed,G1 X0 Y220 F1000 ; prepare for part removal,M84 ; disable motors,M106 S0 ; turn off fan,,M300 S294 P200 ;D4: 294,M300 S588 P200 ;D5: 588,M300 S440 P200 ;A4: 440,M300 S392 P200 ;G4: 392,M300 S784 P200 ;G5: 784,M300 S440 P200 ;A4: 440,M300 S740 P200 ;F#5: 740,M300 S440 P200 ;A4: 440 gcode 0 Star Wars 3000 0.5 0.8 0.8 7200 1002 50 0 1 1.08 0 0 1 1.75|1.75|1.75|1.75|1.75|1.75 17.99|46|46|46|46|46 1.25|1.25|1.25|1.25|1.25|1.25 0 6.92 0 8.44 0 20 1 0 0 1 1 3 1 1 1 3 12 -0.5 600 0 1 30 1 50 200 0.2 0 0 0 1 0 1 1 0.97 0.1 8 4 2 15 30 0.16 6 3 2 100 30 0.3 4 2 2 8 30