Default PLA Medium All Extruders 0 0.4 0 0.42 1 1 5 0.1 0 2700 1 0.5 1 2 1 0.4 0 0.42 1 1 5 0.1 0 2700 1 0.5 1 2 0 0.2 3 3 2 1 2 0 0 0 0 80 100 0.5 0 0 3 2 3 0.14 100 0.3 1 0 1 3 4 1 999 12 1 0.9 0 999 2 1 1 30 1 0 Rectilinear Rectilinear 20 15 100 5 1 45,-45 0 45,-45 0 0 30 0 0 0 0 70 1 0.3 1 1 0 4 45 0 0 0 1 0 1 15 20 0 45 100 0 100 1 0 1 0 0 1 0 0 0 0 1 0 300 300 300 0 0 0 -1 -1 -1 1 -1 1 0,0|0,0|0,0|0,0|0,0|0,0 1 RepRap (Marlin/Repetier/Sprinter) r2 115200 0 G91,G1 Z5,G90,G28.3 Z0,G28,M280 S3.0,G1 X130 Y150,G30 Z0,G1 Z10,G1 X130 Y150,G30 Z1.60,G1 Z10,M280 S7.0 ; Start Tool Change,{IF OLDTOOL=1}{IF NEWTOOL=0}G92 E0.00,{IF OLDTOOL=0}{IF NEWTOOL=1}G92 E0.00,{IF OLDTOOL=1}{IF NEWTOOL=0}G1 E-[toolchange_retract_distance] F[toolchange_retract_speed] ; retract old tool,{IF OLDTOOL=0}{IF NEWTOOL=1}G1 E-[toolchange_retract_distance] F[toolchange_retract_speed] ; retract old tool,T[new_tool],{IF OLDTOOL=1}{IF NEWTOOL=0}G1 X[next_position_x] Y[next_position_y] Z[next_position_z] F[travel_speed],{IF OLDTOOL=0}{IF NEWTOOL=1}G1 X[next_position_x] Y[next_position_y] Z[next_position_z] F[travel_speed],{IF OLDTOOL=1}{IF NEWTOOL=0}G92 E0.00,{IF OLDTOOL=0}{IF NEWTOOL=1}G92 E0.00,{IF OLDTOOL=1}{IF NEWTOOL=0}G1 E[toolchange_prime_distance] F[toolchange_retract_speed] ; un-retract new tool,{IF OLDTOOL=0}{IF NEWTOOL=1}G1 E[toolchange_prime_distance] F[toolchange_retract_speed] ; un-retract new tool,; End Tool Change G1 E-5 F600,G1 X0 Y0 F6000,M104 S0 ; turn off extruder,M140 S0 ; turn off bed,M84 ; disable motors,M300 S4 P1000 ; GERA BEEP, gcode 0 Random Song 3000 0.7 0.8 0.8 4800 1002 50 0 1 1 0 0 0 1.75|1.75|1.75|1.75|1.75|1.75 46|46|46|46|46|46 1.25|1.25|1.25|1.25|1.25|1.25 0 0 0 0 0 20 1 0 1 1 0 3 0 1 0 3 110 -0.5 1200 0 2 10 1 50 200 0.2 0 0 0 1 60 1 225 100 1 195 80 1 220 80 1 0.3 3 3 1 15 25 0.2 3 3 1 20 30 0.1 4 4 2 30 40 0 0 0 0 0 0 1 0 0 G28 ; home all axes 1 1 1 1 1 1 1 0 0 G28 ; home all axes 0 0 0 0 0 0 1 1 0 G91,G1 Z5,G90,G28.3 Z0,G28,M280 S3.0,G1 X130 Y150,G30 Z0,G1 Z10,G1 X130 Y150,G30 Z1.60,G1 Z10,M280 S7.0