Search found 13 matches

Go to advanced search

by rmat
Fri Mar 21, 2014 2:29 am
Forum: Troubleshooting and Bug Reports
Topic: Activation key invalid
Replies: 7
Views: 5081

Re: Activation key invalid

Well for what is worth, mine is still out. Its been 24 hours now since I discovered this and frankly I have to say this is very concernig as I apparently have no control whatsoever of the software I payed for.
by rmat
Thu Mar 20, 2014 6:54 am
Forum: Troubleshooting and Bug Reports
Topic: Wipe While Retracting...
Replies: 42
Views: 20623

Re: Wipe While Retracting...

+1
by rmat
Thu Mar 20, 2014 6:53 am
Forum: Troubleshooting and Bug Reports
Topic: Activation key invalid
Replies: 7
Views: 5081

Re: Activation key invalid

Same here. They probably got some updates or something going on. Code 1020 for me also.
by rmat
Mon Mar 17, 2014 4:33 am
Forum: Feature Requests
Topic: Feature request: Seperate retract/recover speed controls
Replies: 24
Views: 5782

Re: Feature request: Seperate retract/recover speed controls

It's worth noting that Marlin firmware now has support for firmware-based retraction with different retract vs. recover speeds, as well as an optional "auto-retraction" feature that attempts to detect retraction in the incoming g-code and replace it with the firmware-based settings if the slicer do...
by rmat
Wed Mar 05, 2014 1:31 am
Forum: Troubleshooting and Bug Reports
Topic: [FIXED]Perimeters Print Logic Is Wrong
Replies: 12
Views: 5797

Re: Perimeters Print Logic Is Wrong

Actually, i like and dislike this, lets call it feature. It is good in a way that does not overheat one area and thus letting material to settle before applying the next perimeter. But as with all things there are down sides to this also, and as you mentioned, as can help in one area, it can make s*...
by rmat
Wed Mar 05, 2014 1:27 am
Forum: Feature Requests
Topic: [ADDED] Select where layer outlines begin.
Replies: 13
Views: 2698

Re: Feature Request- Select where layer outlines begin.

Bumping to keep this request alive and on top of the list.
by rmat
Wed Mar 05, 2014 1:25 am
Forum: Feature Requests
Topic: Feature request: Seperate retract/recover speed controls
Replies: 24
Views: 5782

Re: Feature request: Seperate retract/recover speed controls

Bump to keep this on top of feature requests.
by rmat
Wed Mar 05, 2014 1:23 am
Forum: General Discussion and Tips
Topic: Feature request
Replies: 17
Views: 4187

Re: Feature request

+1
by rmat
Sat Feb 22, 2014 4:15 am
Forum: Feature Requests
Topic: [ADDED] Select where layer outlines begin.
Replies: 13
Views: 2698

Re: Feature Request- Select where layer outlines begin.

Was trying to do this right now. I was quite used to RepG's lower left layer start order and I assumed disabling random layer starts would produce the same results. Kind of a necessity for me to print some models as I make stuff to sell and hiding the seam (or at least making it consistent) is kind...
by rmat
Sat Feb 22, 2014 4:09 am
Forum: Feature Requests
Topic: Feature request: Seperate retract/recover speed controls
Replies: 24
Views: 5782

Re: Feature request: Seperate retract/recover speed controls

I agree, id does help go a few degrees lower, but with ABS you dont want to go lower than neccesarry to get good bonding, especially if you print mechanical stuff.
Really hope for S3D team to push this feature high on the list, we would all benefit from it, especially bowden users.

Go to advanced search