If a model is sliced at .25mm layer, the gaps are created when supports are added. If "generate support" is unticked the gaps remain.
Search found 9 matches
- Wed Jul 15, 2015 6:36 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Slices missing from print
- Replies: 6
- Views: 3792
- Jump to post
Re: Slices missing from print
Ok, I can somewhat reliably recreate the problem.
If a model is sliced at .25mm layer, the gaps are created when supports are added. If "generate support" is unticked the gaps remain.
If a model is sliced at .25mm layer, the gaps are created when supports are added. If "generate support" is unticked the gaps remain.
- Wed Jul 15, 2015 6:09 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Slices missing from print
- Replies: 6
- Views: 3792
- Jump to post
Re: Slices missing from print
Well, I was able to get the problem to go away. I changed the layer height to .2 and then back to .25 and the gaps vanished. Gremlins...
- Wed Jul 15, 2015 9:18 am
- Forum: Troubleshooting and Bug Reports
- Topic: Slices missing from print
- Replies: 6
- Views: 3792
- Jump to post
Re: Slices missing from print
I've attached the factory file. It looks like they just pushed out an update, so I'm going to install it and see if that helps.
edit: no dice. looks the same
edit: no dice. looks the same
- Tue Jul 14, 2015 9:10 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Slices missing from print
- Replies: 6
- Views: 3792
- Jump to post
Slices missing from print
My pursuit of a perfect Marvin is having some set backs. He's printing with slices missing... I thought perhaps it was a filament problem until I saw the slicing preview.
http://www.thingiverse.com/thing:215703/#files
http://www.thingiverse.com/thing:215703/#files
- Sat Jul 11, 2015 11:17 pm
- Forum: General Discussion and Tips
- Topic: Disappointing results with the Lulzbot Mini
- Replies: 3
- Views: 2248
- Jump to post
Re: Disappointing results with the Lulzbot Mini
Do you need active cooling for XT-Copolyester? It appears Lulzbot actually has the fans turned on in CURA for their ABS profiles. This might sound strange but turning on the fan pretty much fixed my mini's gap problems with ABS (also fixed raft separation).
- Thu Jul 02, 2015 10:35 am
- Forum: Troubleshooting and Bug Reports
- Topic: Upgrade problem 3.0 no preheat before print starts
- Replies: 8
- Views: 3839
- Jump to post
Re: Upgrade problem 3.0 no preheat before print starts
First off, sorry OldGuy57, for hijacking your thread. It appears that our issue is separate albeit similar to yours. Thanks JoeJ, that appears to work around the issue. After deleting the profile and redoing the configuration wizard, the gcode changed on line 235: M190 S[bed0_temperature] ; wait for...
- Wed Jul 01, 2015 1:52 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Upgrade problem 3.0 no preheat before print starts
- Replies: 8
- Views: 3839
- Jump to post
Re: Upgrade problem 3.0 no preheat before print starts
I've attached two files. One is gcode from Cura that works and one is from simplify. I'm not sure why one waits and the other doesn't.
-Mark
-Mark
- Sat Jun 27, 2015 3:27 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Upgrade problem 3.0 no preheat before print starts
- Replies: 8
- Views: 3839
- Jump to post
Re: Upgrade problem 3.0 no preheat before print starts
I'm having the same issue. The "Wait for temperature controller to stabilize before beginning build" is checked for both the extruder and the bed. This is on a lulzbot mini.
- Fri Jun 13, 2014 7:42 am
- Forum: General Discussion and Tips
- Topic: raft separation/ model adhesion
- Replies: 15
- Views: 18974
- Jump to post
Re: raft separation/ model adhesion
Do the support separations settings effect raft separation? It's true that the bed should always be perfectly level etc... however I have to say that having a raft that easily separates would be convenient. It appears that if you elevate the object (change it's abosolute z value) so that it's above ...
