Search found 751 matches

Go to advanced search

by horst.w
Wed Apr 17, 2019 1:55 pm
Forum: Troubleshooting and Bug Reports
Topic: Cannot remove internal supports when you have open the cross section view.
Replies: 4
Views: 49

Re: Cannot remove internal supports when you have open the cross section view.

The same,
but I never had used it in this way ;-)

Bug or not, it is not logical.

horst.w
GER
by horst.w
Wed Apr 17, 2019 3:09 am
Forum: Troubleshooting and Bug Reports
Topic: Coasting issue
Replies: 2
Views: 73

Re: Coasting issue

It seems to be a bug. What coasting has to do is to stop the extrusion of material to relieve pressure in the nozzle and prevent blobs and not interrupting the print line. Bug or not, it will be the question how the coasting-command does work and therefore it can also be a general firmware problem. ...
by horst.w
Fri Apr 12, 2019 2:55 am
Forum: Troubleshooting and Bug Reports
Topic: Problems with Quality (holes)
Replies: 3
Views: 182

Re: Problems with Quality (holes)

Dear all, i finshed a long job (20h) with my jgaurora A5 (Marlin). Sometimes I have blobs and holes, but I really have no Idea what is going on wrong. To my settings PLA: 215 Bed: 70 Retraction Distance: 12mm Retraction Speed 4000 Nozzle Diameter: 0,4 Extrusion Multiplier: 0,93 Coasting: 0,4 Wipe D...
by horst.w
Fri Apr 12, 2019 2:05 am
Forum: Troubleshooting and Bug Reports
Topic: GAP AROUND HOLES
Replies: 4
Views: 615

Re: GAP AROUND HOLES

It's not a bug, it's a question of settings! SolidInfill rectlinear has better results as concentric. When concentric you must also play with overlap up to 100% and the ExtrusionWidth, for FirstLayer also with FirstLayerWidth. And very new in V 4.1.2 also with Z-Offset in tab GCode, because the extr...
by horst.w
Tue Apr 09, 2019 3:43 pm
Forum: Troubleshooting and Bug Reports
Topic: 4.1.2 doesn't retract
Replies: 9
Views: 350

Re: 4.1.2 doesn't retract

PROBLEM DISCERNED I spend the evening in front of my printer. First I tried out a print - always with the same profile but an other model, a little bit smaler structured cylinder than the first modell - and all settings identical but only one process with LH = 0,20 mm. The result is not excelent - ...
by horst.w
Tue Apr 09, 2019 11:24 am
Forum: Troubleshooting and Bug Reports
Topic: 4.1.2 Can't stop Place Surface On Bed
Replies: 0
Views: 61

4.1.2 Can't stop Place Surface On Bed

Hi Once choosen the function " Place Surface on Bed " I cannot stop this function than proceed. CTRL/L or menue is the same. ESC, Undo or others don't help to stop this function, but proceeding it and than click to Undo is running. Not a really serious issue but annoying when the selection was made ...
by horst.w
Tue Apr 09, 2019 11:06 am
Forum: Troubleshooting and Bug Reports
Topic: 4.1.2 doesn't retract
Replies: 9
Views: 350

Re: 4.1.2 doesn't retract

Can't be, it is additional material.

I have print with this profil without any changings (exept First Layer caused by V 4.1.2) a lot of very different objekts, also such as more filigreed as this object is.

H.

PS: ABS , 230 °C
by horst.w
Tue Apr 09, 2019 2:26 am
Forum: Troubleshooting and Bug Reports
Topic: 4.1.2 doesn't retract
Replies: 9
Views: 350

Re: 4.1.2 doesn't retract

Yes, I see! What explanation you have for the objectively existing print issue? I sliced the object many times with different settings and when I returned to my standard profil, notepad++ shows always a different result. Also I have switched between 4.1.2. 4.1.1 and 4.0. After restarting the compute...
by horst.w
Mon Apr 08, 2019 2:42 pm
Forum: Troubleshooting and Bug Reports
Topic: 4.1.2 doesn't retract
Replies: 9
Views: 350

Re: 4.1.2 doesn't retract

... The fist one E -5.5000 is found in the gcode-line 333,093 of 348,022. ... Hi S3D-Jake, thanks for answering! I searched for the typical command E-5.5 what indicates retracts. I'm expecting retractions anytime when the printhead jumbs to the 2nd object, will say, any layer must have two retracts...
by horst.w
Mon Apr 08, 2019 2:47 am
Forum: Troubleshooting and Bug Reports
Topic: 4.1.2 doesn't retract
Replies: 9
Views: 350

Re: 4.1.2 doesn't retract

If the Print Preview shows the reality (not sure), than there are unwished and inexplicably movements of the printhead between the both objects. One of them without retraction.

Additionally the travel moves seem to be doubled.

H.
Retractions_4_2Pro.png
Retractions_3_2Pro.png

Go to advanced search