Search found 852 matches

Go to advanced search

by horst.w
Wed Jul 01, 2020 4:46 pm
Forum: Troubleshooting and Bug Reports
Topic: Slicing problem
Replies: 3
Views: 116

Re: Slicing problem

Cant find any problems, is running fine for me.

Your settings are not optimized but that is not the problem .
Perhaps you have used the Cross Section View and the Z-height was limited.

H.
NoCrossSection.jpg
CrossSection.jpg
by horst.w
Tue Jun 30, 2020 3:00 pm
Forum: Troubleshooting and Bug Reports
Topic: Slicing problem
Replies: 3
Views: 116

Re: Slicing problem

Have a look to tab ADVANCED, perhaps there is set a stop.

horst.w
GER

otherwise please attache a " *.factory " - file here.
To be create with tab FILE >>> Save Factory as ...
by horst.w
Wed Jun 17, 2020 6:40 pm
Forum: General Discussion and Tips
Topic: Recover Lost FFF
Replies: 4
Views: 351

Re: Recover Lost FFF

a litle bit more precise:

the menue point Import FFF-File will accept the format of gcode- files with the extension ".gcode" as well as a .fff - files.

Horst.w
by horst.w
Wed Jun 17, 2020 3:00 am
Forum: General Discussion and Tips
Topic: Recover Lost FFF
Replies: 4
Views: 351

Re: Recover Lost FFF

Import the GCode-Files as "FFF-" , than you can store all informations with "Save Factory-file as ... " into a own folder system.

Good luck!

horst.w
GER
by horst.w
Thu May 07, 2020 4:20 pm
Forum: Troubleshooting and Bug Reports
Topic: Want solid layers to alternate direction
Replies: 3
Views: 3091

Re: Want solid layers to alternate direction

... the actual version 4.1.2 seams to have a problem with the settings of the infill to be print every (1) layer. I have set (1) every layer by using 2 different angles. But it prints only one line direction for 1 layer and the 2nd angle while printing the next upper layer. I can't say when this iss...
by horst.w
Fri May 01, 2020 4:23 am
Forum: General Discussion and Tips
Topic: Flashforge Dreamer TPU settings/profile
Replies: 2
Views: 2089

Re: Flashforge Dreamer TPU settings/profile

Printing TPU is very critical ! Strongly recommended a direct extruder, once I have bought an Anet A8 for this, because my big printer with 70 cm bowden has no chance to work with it , ether TPU hard, TPU middle or TPU soft . TPU has a lot of abstruse preferences. Using normal print temperature make...
by horst.w
Mon Apr 27, 2020 6:46 pm
Forum: Troubleshooting and Bug Reports
Topic: Non-standard ASCII characters in model filenames will wipe all processes
Replies: 3
Views: 1997

Re: Non-standard ASCII characters in model filenames will wipe all processes

Yes, thats right, but the next problem is the printer. Printing from SD, all files names containing "Umlaute" are not listed in the display.

horst.w
GER
by horst.w
Mon Apr 27, 2020 6:40 pm
Forum: General Discussion and Tips
Topic: From .4mm to .6mm
Replies: 3
Views: 2058

Re: From .4mm to .6mm

For print quality it is recommended to set the Layer Height not in a ratio higher than 1 : 2. Will say the maximum LH is 0.30 mm and below when the extrusion width is set to 0.60 mm. Otherwise you must print near a squared extrusion.

horst.w
GER
by horst.w
Thu Apr 09, 2020 3:22 am
Forum: Troubleshooting and Bug Reports
Topic: DUAL EXTRUSION WIZARD CAUSES S3D TO CRASH.
Replies: 5
Views: 10287

Re: DUAL EXTRUSION WIZARD CAUSES S3D TO CRASH.

Never ending story and daily horror?? Same occurrence on Monday. BUT program closed regularly and shutdown the computer . Next day starting the computer (Win 10 - Upgrade from Win 7), ok, all is running except S3D. It didn't start but in the Task-Manager it was listed. Deleting of the SaveState.Fact...
by horst.w
Tue Apr 07, 2020 2:29 pm
Forum: Troubleshooting and Bug Reports
Topic: DUAL EXTRUSION WIZARD CAUSES S3D TO CRASH.
Replies: 5
Views: 10287

Re: DUAL EXTRUSION WIZARD CAUSES S3D TO CRASH.

Hi, on Monday I had also a similar crash (not clear why), but S3D didn't launch anymore. Restarting the computer, deleting S3D from the task manager (3 and 4 instances of S3D at the same time ) , nothing could help. Than, folowing aa advice from the forum here, I searched for the file "savedstate.fa...

Go to advanced search