Search found 17 matches
- Sun Feb 07, 2021 8:21 am
- Forum: General Discussion and Tips
- Topic: PETG on Ender 3 Printing issue
- Replies: 8
- Views: 4711
- Jump to post
Re: PETG on Ender 3 Printing issue
That's what my prints look like when I need to replace the nozzle so if you haven't replaced it in a while you may want to try replacing it as well as the Teflon tube inside the extruder. PETg is harder on your nozzle then say ABS or PLA and I find the nozzles wear out faster with PETg.
- Fri Jun 26, 2020 12:36 pm
- Forum: General Discussion and Tips
- Topic: Version 5 Announcement
- Replies: 113
- Views: 433440
- Jump to post
Re: Version 5 Announcement
Can we rename this thread to:
No Version 5 Announcement
No Version 5 Announcement
- Wed Sep 04, 2019 9:11 pm
- Forum: Feature Requests
- Topic: Support for Resin printers? - AnyCubic Photon and others
- Replies: 23
- Views: 46951
- Jump to post
Re: Support for Resin printers? - AnyCubic Photon and others
Another one to consider please would be the ELEGOO Mars
- Tue Aug 11, 2015 8:17 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Timing assumptions and adjustments?
- Replies: 6
- Views: 3610
- Jump to post
Re: Timing assumptions and adjustments?
Ok, I get that this is hard to calculate. From what I am reading here it sounds exactly what I see at well with my PowerSpec Pro - the estimates are always way off and always on the low side. It seems like something is just not being accounted for in the time calculations. Is anyone getting accurate...
- Sun Feb 22, 2015 10:53 am
- Forum: Troubleshooting and Bug Reports
- Topic: MASSIVE memory leaks
- Replies: 10
- Views: 9491
- Jump to post
Re: MASSIVE memory leaks
Attached is an example after a few Prepare to Print operations.
- Sun Feb 22, 2015 10:23 am
- Forum: Troubleshooting and Bug Reports
- Topic: 2.2.2 is almost perfect for dual extruder prints
- Replies: 13
- Views: 7595
- Jump to post
Re: 2.2.2 is almost perfect for dual extruder prints
I believe the bug is in the Simplify3D code not GPX. If you put the command M133 T1 ; stabilize extruder temperature in the Tool Change G-Code script it works. Simplify3D folks please use the Wait for temperature controller to stabilize setting to automatically put the M133 command in the the G-Code...
- Sat Feb 21, 2015 11:11 pm
- Forum: Troubleshooting and Bug Reports
- Topic: MASSIVE memory leaks
- Replies: 10
- Views: 9491
- Jump to post
MASSIVE memory leaks
When will the massive memory leaks be fixed?
- Sat Feb 21, 2015 11:08 am
- Forum: Troubleshooting and Bug Reports
- Topic: 2.2.2 is almost perfect for dual extruder prints
- Replies: 13
- Views: 7595
- Jump to post
Re: 2.2.2 is almost perfect for dual extruder prints
Yes, thank you gelly!!!
That was my point - yes of course we can work around this by going in and editing the gcode but we all bought this software to do things like that for us and we just want it to work.
That was my point - yes of course we can work around this by going in and editing the gcode but we all bought this software to do things like that for us and we just want it to work.
- Tue Feb 17, 2015 8:58 am
- Forum: Troubleshooting and Bug Reports
- Topic: 2.2.2 is almost perfect for dual extruder prints
- Replies: 13
- Views: 7595
- Jump to post
Re: 2.2.2 is almost perfect for dual extruder prints
JoeJ, Ideally we could set the second extruder to start heating up several layers before the second process kicks in and I think that is possible by setting the temp at the correct layer but this should work. There is a setting for waiting for the extruder heater to stabilize but it does not seem to...
- Sun Feb 15, 2015 10:52 pm
- Forum: Troubleshooting and Bug Reports
- Topic: 2.2.2 is almost perfect for dual extruder prints
- Replies: 13
- Views: 7595
- Jump to post
2.2.2 is almost perfect for dual extruder prints
First I want to thank you for all of the improvements in 2.2.2 for dual prints. It seems like you got all of the issues ironed out except for 1. When i am printing something using both extruders on a PowerSpec 3D Pro using 2 processes with the right extruder printing the first part of the object and...
