Search found 11 matches
- Wed May 24, 2017 1:14 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Break in Slice lines
- Replies: 3
- Views: 1958
- Jump to post
Re: Break in Slice lines
Thanks dkightley. That is what it was. I noticed that the coast feature is not on as a default in Makerbot profile but it is in Ultimaker. Looking at the actual print shows me I still have tuning to do. It is set at 1mm as a default. I'm still learning all the choices of the settings with S3D. Like ...
- Tue May 23, 2017 8:28 am
- Forum: Troubleshooting and Bug Reports
- Topic: Break in Slice lines
- Replies: 3
- Views: 1958
- Jump to post
Re: Break in Slice lines
Thanks for the response. I will check this out tonight , but I did print this as well as others and I thought I saw these anomalies in the print. I will take a closer look and see if they match the slice.
Dom
Dom
- Mon May 22, 2017 8:12 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Break in Slice lines
- Replies: 3
- Views: 1958
- Jump to post
Break in Slice lines
I know my subject is strange sounding but a picture is worth a thousand words, but before you ask let me tell you what I know: 1. this was generated in solidworks 2. saved as an stl 3. brought into S3D version 3.1.1 4. sliced with Ultimaker 2 Extended 5. material : PLA 6. checked for any errors with...
- Sun Jan 31, 2016 6:06 pm
- Forum: General Discussion and Tips
- Topic: Finding profiles
- Replies: 2
- Views: 1614
- Jump to post
Re: Finding profiles
Thanks it's been a long time since I had to add a printer.
- Sun Jan 31, 2016 5:14 pm
- Forum: General Discussion and Tips
- Topic: Finding profiles
- Replies: 2
- Views: 1614
- Jump to post
Finding profiles
Where do you go to download profiles for different printers?
- Fri May 22, 2015 8:19 am
- Forum: General Discussion and Tips
- Topic: Understanding the speed algorithms in models
- Replies: 4
- Views: 2456
- Jump to post
Re: Understanding the speed algorithms in models
I knew about the hoovering comment but as a mechanical engineer, an example of what happens when the number goes higher or lower would help me more.
As for the links they are very helpful thanks.
Dom
As for the links they are very helpful thanks.
Dom
- Thu May 21, 2015 11:24 am
- Forum: General Discussion and Tips
- Topic: Understanding the speed algorithms in models
- Replies: 4
- Views: 2456
- Jump to post
Understanding the speed algorithms in models
Hi, I am using a Makerbot Dual, I have a simple l right angle bracket about 1/2" wide and extending about 1/4" x 1/8" thick on each side. It slices fine but I notice in the preview that the surface on the base plate runs around 1700 mm/min and then when it goes to do the vertical leg ...
- Mon Dec 29, 2014 2:33 pm
- Forum: General Discussion and Tips
- Topic: What Firmware to use with Simplify3D
- Replies: 2
- Views: 1550
- Jump to post
- Mon Dec 29, 2014 1:43 pm
- Forum: General Discussion and Tips
- Topic: What Firmware to use with Simplify3D
- Replies: 2
- Views: 1550
- Jump to post
What Firmware to use with Simplify3D
Hi,
I have a MakerBot 1 Dual and I plan on using S3D, What firmware should I be using? Does it matter?
Dom
I have a MakerBot 1 Dual and I plan on using S3D, What firmware should I be using? Does it matter?
Dom
- Fri Nov 07, 2014 3:31 pm
- Forum: General Discussion and Tips
- Topic: MakerBot Replicator Dual and a Delta with Simplify3D
- Replies: 3
- Views: 3452
- Jump to post
Re: MakerBot Replicator Dual and a Delta with Simplify3D
Sorry I'm confused. the Rep 2 is not the Rep Dual. The Rep Dual is the wood construction with two heads. First was the Replicator then the Dual then the Rep 2, then the Rep 2x, and now the 5th generation. The supported printers states Rep 1, Rep 2 and Rep 2x.
