Search found 9 matches

Go to advanced search

by turbocharged110
Thu Aug 27, 2015 9:08 am
Forum: Feature Requests
Topic: Cloud Profile Sync
Replies: 17
Views: 20887
 
Jump to post

Re: Share setting between computers?

KC_703 wrote:
jeand wrote:
BaudR8 wrote: 2) Filename is empty. Need to retype it... Booooring...
But it woooorrrkkkssss!
But it can work better
by turbocharged110
Tue Aug 25, 2015 1:06 pm
Forum: General Discussion and Tips
Topic: Stratification
Replies: 6
Views: 3145
 
Jump to post

Re: Stratification

Have you tried the same part with different layer heights? Could be a rounding error where your microsteps don't match the desired Z-height, so every X layers will be lower than the others with the same material extruded.
by turbocharged110
Tue Aug 25, 2015 9:37 am
Forum: Feature Requests
Topic: Water Soluble Support
Replies: 15
Views: 9930
 
Jump to post

Re: Water Soluble Support

Just want to bump this up.

KISSlicer can and has been able to do this for a long time now.
KS_materials.png
by turbocharged110
Tue Aug 18, 2015 3:52 pm
Forum: Feature Requests
Topic: Cloud Profile Sync
Replies: 17
Views: 20887
 
Jump to post

Re: Share setting between computers?

So not as easy as my KISSlicer setup, but I started saving my FFF profiles to my dropbox folder on each machine each time I close the program and reopen it each time I open it. This is a bit of work, but at least I can keep my configuration consistent between machines.
by turbocharged110
Sat Aug 08, 2015 12:43 pm
Forum: Feature Requests
Topic: Cloud Profile Sync
Replies: 17
Views: 20887
 
Jump to post

Cloud Profile Sync

I currently run Simplify3D on two computers and would like to share settings between the two without having to export/import each time I switch machines. This is easy with KISSlicer since it saves the settings files to the same directory as the .exe which I have placed in my local Dropbox folder on ...
by turbocharged110
Fri Jan 23, 2015 4:17 pm
Forum: Troubleshooting and Bug Reports
Topic: Rafts in V2.2.1
Replies: 11
Views: 4383
 
Jump to post

Re: Rafts in V2.2.1

There are definitely good uses for a raft (better first layer support adhesion for support material that lies outside the perimeter of the part is when I use rafts most), but that doesn't answer the question at hand. I never used rafts in V2.2.0 since I got it just before V2.2.1 came out so I can't ...
by turbocharged110
Sun Jan 18, 2015 11:07 am
Forum: General Discussion and Tips
Topic: Tip of the Day 4- Layer tab, a technical analysis
Replies: 15
Views: 77029
 
Jump to post

Re: Tip of the Day 4- Layer tab, a technical analysis

First Layer Height: This % will take a % of your Primary Layer Height. If you are printing with a small Primary Layer Height like .1 mm I would recommend a First Layer Height of 250%, to get about a resulting .25 mm first layer height If your First Layer Height is below 100%, the extrusion amount w...
by turbocharged110
Wed Jan 07, 2015 8:52 am
Forum: Feature Requests
Topic: [ADDED] More options for stronger infill.
Replies: 56
Views: 41342
 
Jump to post

Re: More options for stronger infill.

I still think increasing extrusion width for infill to make stronger parts is a crutch and that better infill patterns is an absolute must for the long term. My absolute favorite is Kisslicer's rounded infill...it's not quite as strong as true hex, but close and WAY faster to print. I haven't been b...

Go to advanced search