Search found 17 matches

Go to advanced search

by adamfilip
Wed May 23, 2018 9:08 pm
Forum: Feature Requests
Topic: Mouse Ears
Replies: 1
Views: 525

Mouse Ears

I manually add mouse ears (10mm single layer circles) near the corners of my prints to help prevent warping. I prefer this over a brim as its on in select areas, and requires less cleanup wish there was a way to add automatically, and be able to specify spacing, diameter, layers, and offset from cor...
by adamfilip
Wed May 23, 2018 8:55 pm
Forum: Feature Requests
Topic: Hole Adjust
Replies: 2
Views: 693

Hole Adjust

Often exterior dimensions are correct but holes are too small. should be a Dimensional Adjustment that just affects holes,
by adamfilip
Tue Jul 04, 2017 3:29 pm
Forum: Feature Requests
Topic: Belt Z / Angled Head Support
Replies: 1
Views: 759

Belt Z / Angled Head Support

Hoping S3D will add support for machines with Belt Bed Z platform / Infinite bed. and printing on a 45 degree angle like this printer

https://printrbot.com/shop/printrbelt/
by adamfilip
Tue Oct 18, 2016 10:49 am
Forum: General Discussion and Tips
Topic: Need some suggestions to improve print quality
Replies: 0
Views: 770

Need some suggestions to improve print quality

Trying to improve print quality with my Custom COREXY machine Running PETG at 255 degrees, with 70 degree PEI Bed I have also run at 235 degrees with similar print quality Extruder is a Bondtech Mini Direct Bowden Bowden tube is aprox 400mm E3D V6 Bowden 1.75 with .4mm nozzle Simplify 3D Settings .4...
by adamfilip
Thu Dec 17, 2015 1:36 pm
Forum: Feature Requests
Topic: Feature Request : Mouse Ears
Replies: 4
Views: 1307

Re: Feature Request : Mouse Ears

yes but removing a brim for an entire model is a pain. easier to just remove a few disks.
by adamfilip
Wed Dec 16, 2015 4:01 pm
Forum: Feature Requests
Topic: Feature Request : Mouse Ears
Replies: 4
Views: 1307

Feature Request : Mouse Ears

I would like to be able to easly add a Brim or Mouse ears to spefici areas of the model to help prevent curling. or even better for it to be able to tell where curling might occur and automatically add them to those areas.
by adamfilip
Wed Dec 16, 2015 3:58 pm
Forum: Feature Requests
Topic: FEATURE REQUEST : Run Code every X layers
Replies: 2
Views: 551

FEATURE REQUEST : Run Code every X layers

I would like to be able to run some custom code, at a set interval of layers that I set.

For example. If I wanted to add some code for the hotend to move X&Y over to a wiping station every 10 layers, to clean the Nozzle
and then continue back onto the next layer
by adamfilip
Thu Jul 23, 2015 11:35 pm
Forum: Troubleshooting and Bug Reports
Topic: S3D 3.01 Long Pauses - Makerfarm 12"
Replies: 4
Views: 778

Re: S3D 3.01 Long Pauses - Makerfarm 12"

tired printing the same file using the same settings with S3D 2.2 and no pauses.. works normal
by adamfilip
Thu Jul 23, 2015 11:14 pm
Forum: Troubleshooting and Bug Reports
Topic: S3D 3.01 Long Pauses - Makerfarm 12"
Replies: 4
Views: 778

Re: S3D 3.01 Long Pauses - Makerfarm 12"

Baud is set to 250000, same as it was with S3D 2.2
yes over USB, havent tried via SD card
by adamfilip
Thu Jul 23, 2015 8:45 pm
Forum: Troubleshooting and Bug Reports
Topic: S3D 3.01 Long Pauses - Makerfarm 12"
Replies: 4
Views: 778

S3D 3.01 Long Pauses - Makerfarm 12"

Just tried S3D 3.01 and so far im getting very long pauses (5 sec) between moves
not sure whats going on.

any advice please

Go to advanced search