Search found 6 matches
- Wed Feb 25, 2015 3:13 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Problems with beginning of print
- Replies: 8
- Views: 3173
- Jump to post
Re: Problems with beginning of print
as promised... with sticky parameters on ; G-Code generated by Simplify3D(R) Version 2.2.2 ; Feb 25, 2015 at 9:11:39 ; Settings Summary ; processName,Sparkcube ; applyToModels,muendung ; profileLabel,sparkcube.fff ; printMaterial,PLA ; printQuality,Medium ; extruderName,Primary Extruder ; extruderTo...
- Wed Feb 25, 2015 5:40 am
- Forum: Troubleshooting and Bug Reports
- Topic: Problems with beginning of print
- Replies: 8
- Views: 3173
- Jump to post
Re: Problems with beginning of print
i can post a gcode file when i'm back home...
atm I can say, that my printer actually moves from the home position to 0 0 0 at the beginning of the print.
which means my printer heats up to printing temperature, then it homes to 200 200 0, then moves to 0 0 0 and from there it begins to print.
atm I can say, that my printer actually moves from the home position to 0 0 0 at the beginning of the print.
which means my printer heats up to printing temperature, then it homes to 200 200 0, then moves to 0 0 0 and from there it begins to print.
- Tue Feb 24, 2015 12:11 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Problems with beginning of print
- Replies: 8
- Views: 3173
- Jump to post
Re: Problems with beginning of print
my home location isn't 0 0 0, but 200 200 0
so after heating up, my printer homes to 200 200 0, then moves across the whole platform to 0 0 0 and back to the binning position of the print.
with or without sticky parameters - it's the same behavior
so after heating up, my printer homes to 200 200 0, then moves across the whole platform to 0 0 0 and back to the binning position of the print.
with or without sticky parameters - it's the same behavior
- Mon Feb 23, 2015 9:16 am
- Forum: Troubleshooting and Bug Reports
- Topic: Problems with beginning of print
- Replies: 8
- Views: 3173
- Jump to post
Re: Problems with beginning of print
and btw. if i check sticky parameters...
in the preview window i can see the travel movement to X0 Y0 Z0, it just doesn't appear in the G-Code File.
This even happens with the standard start/stop scipts
in the preview window i can see the travel movement to X0 Y0 Z0, it just doesn't appear in the G-Code File.
This even happens with the standard start/stop scipts
- Mon Feb 23, 2015 8:47 am
- Forum: Troubleshooting and Bug Reports
- Topic: Problems with beginning of print
- Replies: 8
- Views: 3173
- Jump to post
Re: Problems with beginning of print
tested with a new profile...
everything looks fine - until i uncheck sticky parameters... as soon as i uncheck it the G1 X0 Y0 Z0 appears in front of the first layer...
don't know if my repetier firmware supports these
everything looks fine - until i uncheck sticky parameters... as soon as i uncheck it the G1 X0 Y0 Z0 appears in front of the first layer...
don't know if my repetier firmware supports these
- Sun Feb 22, 2015 4:09 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Problems with beginning of print
- Replies: 8
- Views: 3173
- Jump to post
Problems with beginning of print
Hi there, i have an annoying thing in the G-Code of S3D.. my printer (SparkCube) homes at X max, Y max and Z min... S3D adds a movement to X0 Y0 Z0 after my startscript, which means the nozzle travels across the whole platform only to travel half way back to the center to start the print while leavi...
