Search found 11 matches
- Sat Aug 10, 2019 10:08 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Need some quick help
- Replies: 1
- Views: 1291
- Jump to post
Re: Need some quick help
Well, I figured it out guys. Somehow, the max for the X axis got changed in the arduino files. Just went in and changed it back....good to go.
- Sat Aug 10, 2019 7:31 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Need some quick help
- Replies: 1
- Views: 1291
- Jump to post
Need some quick help
I have been using Simplify 3D for over 5 years with no problems. I am using a MendelMax 1.5 printer. Just recently, it will no longer print the full width of the print bed. Y and Z axis are fine, but the X axis is not. It stops about 25 mm short of going all of the way across the bed. I have reset t...
- Thu Nov 12, 2015 8:55 am
- Forum: General Discussion and Tips
- Topic: Saving after adding support
- Replies: 3
- Views: 1741
- Jump to post
Re: Saving after adding support
Thank you very much gentlemen.
Milt
Milt
- Wed Nov 11, 2015 11:26 am
- Forum: General Discussion and Tips
- Topic: Saving after adding support
- Replies: 3
- Views: 1741
- Jump to post
Saving after adding support
I have taken a file and added quite a bit of support to get it to print correctly. How can I save the file so that I can use it again without having to redo the support. Or, is this not possible?
Milt
Milt
- Wed Nov 11, 2015 11:24 am
- Forum: General Discussion and Tips
- Topic: Windows 10 little trinket of joy.
- Replies: 4
- Views: 2890
- Jump to post
Re: Windows 10 little trinket of joy.
So, where does one find the program?
Milt
Milt
- Wed Sep 09, 2015 12:08 pm
- Forum: Feature Requests
- Topic: TIme estimate
- Replies: 3
- Views: 2856
- Jump to post
Re: TIme estimate
I did do the research in the forum. I failed to see any of the posts that actually offered a solution to the problem. When I use Repetier to do my slicing, it is quite close to the actual time it takes to do a print. So, I did a post to see what might be done for this. Just looking for an answer to ...
- Tue Sep 08, 2015 8:24 pm
- Forum: Feature Requests
- Topic: TIme estimate
- Replies: 3
- Views: 2856
- Jump to post
Re: TIme estimate
Nobody else has this problem, I guess. Oh well.
Milt
Milt
- Sun Sep 06, 2015 10:25 pm
- Forum: Feature Requests
- Topic: TIme estimate
- Replies: 3
- Views: 2856
- Jump to post
TIme estimate
Has anyone else had problems with the time to print estimator? I just did a .1mm print with 75% fast honeycomb infill. The estimated time was 1 hour and 44 minutes, it actually took 3 hours and 15 minutes. That is a lot more than the estimate. I had to quit the print as I had to leave the house on a...
- Tue Jun 16, 2015 1:48 pm
- Forum: Feature Requests
- Topic: [ADDED] Retrieving product codes
- Replies: 3
- Views: 2921
- Jump to post
Re: Product codes
I already know that. I have been waiting for over 3 hours to get my product code. This should not happen. That is why a request like this should be addressed. I now can not use my printer, this could be easily solved by having a spot on the website to get the codes for paid software. That is why I h...
- Tue Jun 16, 2015 12:44 pm
- Forum: Feature Requests
- Topic: [ADDED] Retrieving product codes
- Replies: 3
- Views: 2921
- Jump to post
[ADDED] Retrieving product codes
A feature I would like to see, and I believe is essential to the smooth, continued operation of the software is to have an immediate way to recover lost product codes. Most sites have a 'my account' option which would provide the software purchased, the amount of the software and the product key ass...
