Search found 1555 matches

Go to advanced search

by S3D-Jason
Tue Feb 11, 2025 1:25 pm
Forum: Troubleshooting and Bug Reports
Topic: Crash on open due to corrupted saved state
Replies: 5
Views: 1452
 
Jump to post

Re: Crash on open due to corrupted saved state

You can always email it directly to our team at the link below:
https://www.simplify3d.com/contact-us/
by S3D-Jason
Tue Feb 11, 2025 1:24 pm
Forum: General Discussion and Tips
Topic: QIDI PRO Slicer software possible issue
Replies: 1
Views: 160
 
Jump to post

Re: QIDI PRO Slicer software possible issue

Are you using Simplify3D? Can you confirm which exact profile you are using?
by S3D-Jason
Tue Feb 11, 2025 1:23 pm
Forum: General Discussion and Tips
Topic: Simplify3D Print Bed Calibration Issues
Replies: 1
Views: 100
 
Jump to post

Re: Simplify3D Print Bed Calibration Issues

Many times each software program will have a separate Z offset that determines the position of all other coordinates in the gcode file. So the auto-leveling just makes sure things are level, but the Z offset in the slicer basically moves the print up or down to either squish it into the bed more, or...
by S3D-Jason
Thu Feb 06, 2025 1:05 pm
Forum: Troubleshooting and Bug Reports
Topic: Bug: v5.1.2 adds plane where it doesn't belong
Replies: 1
Views: 243
 
Jump to post

Re: Bug: v5.1.2 adds plane where it doesn't belong

It could definitely help to attach a factory file so others could try to reproduce the issue. I should also mention that V5 added several new slicing modes to help it deal with different mesh issues. They are explained in more detail on this page: https://www.simplify3d.com/resources/articles/identi...
by S3D-Jason
Mon Feb 03, 2025 10:04 am
Forum: General Discussion and Tips
Topic: bambu connect
Replies: 1
Views: 292
 
Jump to post

Re: bambu connect

On their wiki they already talk about running gcode from 3rd party apps, so that should still be possible https://wiki.bambulab.com/en/software/bambu-connect?ref=blog.bambulab.com "To start a print, import the gcode or 3MF file by either dragging and dropping the file in Bambu Connect, or by cl...
by S3D-Jason
Tue Jan 28, 2025 1:27 pm
Forum: Troubleshooting and Bug Reports
Topic: Software closes 2 seconds after opening
Replies: 1
Views: 166
 
Jump to post

Re: Software closes 2 seconds after opening

Here's a recent thread that was very similar. I bet the same solution would work for what you described.
viewtopic.php?p=73961
by S3D-Jason
Thu Jan 23, 2025 2:02 pm
Forum: General Discussion and Tips
Topic: Start Gcode Query - Creatbot F430
Replies: 1
Views: 158
 
Jump to post

Re: Start Gcode Query - Creatbot F430

If you're new to gcode, there's a useful tutorial here that explains most of the common commands: https://www.simplify3d.com/resources/articles/3d-printing-gcode-tutorial/ The script that you posted looks like it was written for a different slicer, so there are several commands you would need to cha...
by S3D-Jason
Thu Jan 23, 2025 1:57 pm
Forum: General Discussion and Tips
Topic: Feature based layer dependent acceleration changes
Replies: 6
Views: 752
 
Jump to post

Re: Feature based layer dependent acceleration changes

Is it possible to add a feature in Simplify3D that can automatically change acceleration based on different actions, like for extruding or travel moves Yes, the steps I mentioned above can actually be used to do exactly that! Go to Edit Process Settings > Output tab, and turn on the "Include M...
by S3D-Jason
Mon Jan 20, 2025 2:44 pm
Forum: Troubleshooting and Bug Reports
Topic: Specific Print's Acceleration Is Too High!
Replies: 4
Views: 590
 
Jump to post

Re: Specific Print's Acceleration Is Too High!

Good investigation! I can't imagine any machine that moves at 200+ mm/sec wouldn't be using acceleration at all, so it's probably more likely the acceleration is just set too high in the firmware. The whole point of acceleration is to prevent steps from skipping when you try to move at the desired s...
by S3D-Jason
Mon Jan 20, 2025 2:41 pm
Forum: General Discussion and Tips
Topic: Feature based layer dependent acceleration changes
Replies: 6
Views: 752
 
Jump to post

Re: Feature based layer dependent acceleration changes

If you want all the travel moves to use a different acceleration, you could consider turning on the M101/M102/M103 commands (Edit Process Settings > Output tab). The M101 comes before the extrusion starts, M102 after it stops, and M103 before a potential retraction. So to use a different acceleratio...

Go to advanced search