Search found 7 matches
- Fri Aug 07, 2015 2:53 am
- Forum: General Discussion and Tips
- Topic: CubePro Compatibility
- Replies: 76
- Views: 102419
- Jump to post
Re: CubePro Compatibility
I have had this issue too and had to strip the motors down to free the filament. In my experience there are a few things that can make this happen though. Wrong extruder temps is one reason. I run the PLA at 210 for first layer then 200. If you are doing a mixed material build with ABS and PLA, I f...
- Wed Aug 05, 2015 10:14 am
- Forum: General Discussion and Tips
- Topic: CubePro Compatibility
- Replies: 76
- Views: 102419
- Jump to post
Re: CubePro Compatibility
Hi, I've a new problem with my cubepro profile. Like I said in my last messages, I can extude ABS without issue. But for few days, I have tried to extrude PLA to create support. With the Cubepro software, there is no problem, but with S3D after 5 or 6 mm, the printing stops with the error code F22. ...
- Tue Jun 23, 2015 2:31 am
- Forum: General Discussion and Tips
- Topic: CubePro Compatibility
- Replies: 76
- Views: 102419
- Jump to post
Re: CubePro Compatibility
I think I finally found the problem : there was five layers for the outline shells, but the workpiece outline width was slightly greater than the width of five fill. So I think that the software increase the extruder flowrate to extrude a larger last fill. I tried with only one layer for the outline...
- Fri Jun 19, 2015 3:49 am
- Forum: General Discussion and Tips
- Topic: CubePro Compatibility
- Replies: 76
- Views: 102419
- Jump to post
Re: CubePro Compatibility
In fact, it's happening on the last fill, inner or outter. I changed bedplate Z offset to get a correct gap with the extruder because there was more than 1mm when I used your fff profile. The gap between the plate and the extruder is about 0,15 mm (printer user's guide preconizes 0,1 mm). Only the f...
- Thu Jun 18, 2015 4:52 am
- Forum: General Discussion and Tips
- Topic: CubePro Compatibility
- Replies: 76
- Views: 102419
- Jump to post
Re: CubePro Compatibility
Hello, I need your help again ! The printer works fine with the current parameters but there is a little problem with the last perimeter extruded. As you can see on the following picture, the last perimeter quality is bad compare to the first (the outside perimeter is the first printed and the insid...
- Mon Jun 08, 2015 8:41 am
- Forum: General Discussion and Tips
- Topic: CubePro Compatibility
- Replies: 76
- Views: 102419
- Jump to post
Re: CubePro Compatibility
@MichaelHerron :
Thanks for your answer! The extrusion width was 0.40 in the extruder tab, so I slowed the print down without touching the flow-rate and the print quality is impoved.
I will continue to test the printer with Simplify3D.
Thanks for your answer! The extrusion width was 0.40 in the extruder tab, so I slowed the print down without touching the flow-rate and the print quality is impoved.
I will continue to test the printer with Simplify3D.
- Fri Jun 05, 2015 5:31 am
- Forum: General Discussion and Tips
- Topic: CubePro Compatibility
- Replies: 76
- Views: 102419
- Jump to post
Re: CubePro Compatibility
First, I'm French, so excuse me for my English, it's not my mother tongue. I'm new on this forum, I found it while I was searching how could I improve the print quality of our Cubepro Trio. Thanks for sharing your profiles lepino! It works in quite well with our cubepro trio. But there is a little p...
