Search found 14 matches

Go to advanced search

by mpd352
Sun Dec 26, 2021 8:52 pm
Forum: Troubleshooting and Bug Reports
Topic: GeeeTech A10T and ABS
Replies: 6
Views: 1041
 
Jump to post

Re: GeeeTech A10T and ABS

The parts printed OK on my A10T. Only mistake was failing to change the extruder for the brim to the left side spool, which was black ABS. It was set to the right, which was red PLA. Never the less, they printed. New Parts.jpg The new parts are on the bottom, and the broken original right hand piece...
by mpd352
Sun Dec 26, 2021 4:23 pm
Forum: Troubleshooting and Bug Reports
Topic: GeeeTech A10T and ABS
Replies: 6
Views: 1041
 
Jump to post

Re: GeeeTech A10T and ABS

Test Piece.jpg
The simple 40mm x 40mm x 2mm rectangle printed OK. Some corner curling.

I'll try next with the brim airscapes recommended.
by mpd352
Sun Dec 26, 2021 2:11 pm
Forum: Troubleshooting and Bug Reports
Topic: GeeeTech A10T and ABS
Replies: 6
Views: 1041
 
Jump to post

Re: GeeeTech A10T and ABS

As a test, I let the job run to completion. But, unfortunately, what I found was an issue with the raft and only the raft. The first layer of the raft laid down correctly. However, the second and subsequent layers of the raft are a mess. I suspect that the second and third layers of the raft are ext...
by mpd352
Sat Dec 25, 2021 3:00 pm
Forum: Troubleshooting and Bug Reports
Topic: GeeeTech A10T and ABS
Replies: 6
Views: 1041
 
Jump to post

Re: GeeeTech A10T and ABS

Thanks for your reply. I do have an enclosure. I'll have to dig it out and try it.

Thanks!
by mpd352
Sat Dec 25, 2021 2:19 pm
Forum: Troubleshooting and Bug Reports
Topic: GeeeTech A10T and ABS
Replies: 6
Views: 1041
 
Jump to post

GeeeTech A10T and ABS

I’m trying to print ABS with my A10T. I need something a little more durable than PLA. I’ve read and re-read the tips and tricks for printing ABS, and am hitting a wall. I’ve set the file to print with a raft, cooling fans off, print temp at 222C and bed temp at 100C to start, then dropping to 85C. ...
by mpd352
Mon May 03, 2021 3:32 pm
Forum: Troubleshooting and Bug Reports
Topic: GeeeTech A20T Profile
Replies: 2
Views: 2304
 
Jump to post

GeeeTech A20T Profile

Is anyone using a GeeeTech A20T multi-color printer, and if you are do you have a working profile for it?

Thanks,

Kevin
by mpd352
Fri Mar 05, 2021 2:53 pm
Forum: General Discussion and Tips
Topic: Gcode for A10T Purge Bucket
Replies: 0
Views: 1494
 
Jump to post

Gcode for A10T Purge Bucket

I have a GeeeTech A10T printer. I’m trying to implement a purge bucket to improve my multicolor prints. I’m not very familiar with G code, and the more I read the more confused I get. I have managed to move the axis over to where the purge bucket will be through direct input to the machine, so I kno...
by mpd352
Wed Mar 03, 2021 8:49 pm
Forum: Troubleshooting and Bug Reports
Topic: Change the X-Axis limits in firmware A10T
Replies: 0
Views: 1070
 
Jump to post

Change the X-Axis limits in firmware A10T

I have a GeeeTech A10T. When I move the X axis to the left, using the printer control panel, it hits 0 mm a full 20 mm inside the left edge of the build plate. To the right, 220 mm is about 5 mm inside the right edge. I want to install a purge bucket for multicolor printing, so at least to the left ...
by mpd352
Wed Jan 20, 2021 10:17 pm
Forum: General Discussion and Tips
Topic: Single Extruder Three Spool Printing
Replies: 2
Views: 764
 
Jump to post

Re: Single Extruder Three Spool Printing

Thanks. I'd read that before, but missed the part where I had to use the "Select Models" button in the process dialog to assign the specific process to a specific part of the model.

Thanks, I'm off and running.

K
by mpd352
Tue Jan 19, 2021 10:47 pm
Forum: General Discussion and Tips
Topic: Single Extruder Three Spool Printing
Replies: 2
Views: 764
 
Jump to post

Single Extruder Three Spool Printing

I have a GeeeTech A10T printer. This has a single hot end, but supports three filament schools/colors all fed through the single hot end. I want to do multicolor prints, and have done some based on the layer principle, where different layers are different colors. There is a three-color gecko multi-m...

Go to advanced search