- 12741878_695457263890125_2380230011329536178_n.jpg (19.25 KiB) Viewed 1491 times
Search found 8 matches
- Sun Feb 21, 2016 5:27 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Bed Bug
- Replies: 2
- Views: 1491
- Jump to post
Bed Bug
Hey, Did anyone have this problem?
- Sat Aug 22, 2015 6:48 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Bad quality in TOP / LAST layers
- Replies: 16
- Views: 11644
- Jump to post
Re: Bad quality in TOP / LAST layers
solid cubes dont tell you too much. you need to do a thin wall cube. in advanced tab check "merge all outlines into solid model", set infill to 0, top and bottom layers 0. perimeter walls 2. when done measure the thickness of the wall. it should measure 2x your extrusion width setting. if...
- Sat Aug 22, 2015 6:46 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Bad quality in TOP / LAST layers
- Replies: 16
- Views: 11644
- Jump to post
Re: Bad quality in TOP / LAST layers
Now im seeing problems in all my prints. The wavy lines are everywhere. I'm getting upset cause i didn't change nothing...
Problems:
1- Horrible top layers
2- Wavy Lines
Problems:
1- Horrible top layers
2- Wavy Lines
- Thu Aug 20, 2015 11:11 am
- Forum: Troubleshooting and Bug Reports
- Topic: Bad quality in TOP / LAST layers
- Replies: 16
- Views: 11644
- Jump to post
Re: Bad quality in TOP / LAST layers
Look what happened with calibration CUBE. The side is pretty nice. PLA
Z Offset 0.8
Extrusion Multiplier 1
Default printing speed 3600,0 mm/min
Temperature 210
Order of photos are BOTTOM/TOP/
The Bottom layer is now soft with an 0.7 Z OFFSET
Z Offset 0.8
Extrusion Multiplier 1
Default printing speed 3600,0 mm/min
Temperature 210
Order of photos are BOTTOM/TOP/
The Bottom layer is now soft with an 0.7 Z OFFSET
- Wed Aug 19, 2015 7:39 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Bad quality in TOP / LAST layers
- Replies: 16
- Views: 11644
- Jump to post
Re: Bad quality in TOP / LAST layers
Thefilament dia is correct at 1.75mm.jimc wrote:You dont just set the multiplier to whatever you want. You need to print a thin wall calibration cube, and take measurements to set the multiplier. Start by setting the filament dia correctly as that works hand and hand with multiplier to calculate flow.
- Wed Aug 19, 2015 11:00 am
- Forum: Troubleshooting and Bug Reports
- Topic: Bad quality in TOP / LAST layers
- Replies: 16
- Views: 11644
- Jump to post
Re: Bad quality in TOP / LAST layers
Ok, i will try it. This happens ONLY with PLA.
When i switch to ABS i have the next problem: Top layers is ROUGH. This photo is with 1.00 extrusion multiplier. With 0.9 extrusion multiplier i can see little gaps between lines. So i have to play between 0.9 and 1.0 ?
When i switch to ABS i have the next problem: Top layers is ROUGH. This photo is with 1.00 extrusion multiplier. With 0.9 extrusion multiplier i can see little gaps between lines. So i have to play between 0.9 and 1.0 ?
- Tue Aug 18, 2015 7:52 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Bad quality in TOP / LAST layers
- Replies: 16
- Views: 11644
- Jump to post
Re: Bad quality in TOP / LAST layers
cant find the extrusion multiplier. Solid infill underspeed was at 80% and switched to 70%KeyboardWarrior wrote:You may want to increase your Extrusion Multiplier (Extruder Tab) slightly, and also slow down your Solid Infill Underspeed (Other tab) to get a really nice finish on the top of your prints.
- Tue Aug 18, 2015 8:55 am
- Forum: Troubleshooting and Bug Reports
- Topic: Bad quality in TOP / LAST layers
- Replies: 16
- Views: 11644
- Jump to post
Bad quality in TOP / LAST layers
Hey, I'm having this issue.. My printer is an "ROBO 3D R1" and when i print i got some bad layers at top.
Here is an example
I was thinking it can be a slicing problem
Here is an example
I was thinking it can be a slicing problem
