thank you, I hadn't find it when i checked the forum.
Hope it will be solved soon
bye
Search found 7 matches
- Tue Nov 20, 2018 3:04 am
- Forum: Troubleshooting and Bug Reports
- Topic: [FIXED] V4.1 brim "around" models not "between"
- Replies: 4
- Views: 2304
- Jump to post
- Fri Nov 16, 2018 5:13 am
- Forum: Troubleshooting and Bug Reports
- Topic: [FIXED] V4.1 brim "around" models not "between"
- Replies: 4
- Views: 2304
- Jump to post
Re: V4.1 brim "around" models not "between"
Hi all, Does nobody observe the same behaviour?.... anyway, I would like to report also a bug (i think) in the last version of the software. When I duplicate a model with support, the software creates the number selected but really without support even if I specify to reproduce them. I can see suppo...
- Tue Nov 13, 2018 7:47 am
- Forum: Troubleshooting and Bug Reports
- Topic: [FIXED] V4.1 brim "around" models not "between"
- Replies: 4
- Views: 2304
- Jump to post
[FIXED] V4.1 brim "around" models not "between"
Hi all, I recently upgraded software to new version. I notice that, having multiple object on plate, brim is create only "around" the group and not inside, between the objects. I know I can separate them, but I need to use as much space as i can, so i need to take them close one each other...
- Mon Jan 11, 2016 1:26 pm
- Forum: Troubleshooting and Bug Reports
- Topic: badprinter2 second extruder offset
- Replies: 5
- Views: 3756
- Jump to post
Re: badprinter2 second extruder offset
After i did some tests, i used succesfully the script tab in the Process Settings. I add the instruction M218 T1 X26.0 in the gcode so the second extruder worked properly, except for a 0.5 mm misalignment between the part printed with first extruder and the part printed with the second one. Must che...
- Thu Nov 26, 2015 9:05 am
- Forum: Troubleshooting and Bug Reports
- Topic: badprinter2 second extruder offset
- Replies: 5
- Views: 3756
- Jump to post
Re: badprinter2 second extruder offset
ok , goti it. I'll check this configuration
Thank You very much
Thank You very much
- Wed Nov 25, 2015 12:56 pm
- Forum: Troubleshooting and Bug Reports
- Topic: badprinter2 second extruder offset
- Replies: 5
- Views: 3756
- Jump to post
Re: badprinter2 second extruder offset
You need to set the offsets in the firmware as well. I believe with marlin you can use the M218 command. For example, to set the T1 offset to be 32mm in the X-direction, you could use M218 T0 X32.0 Read here for more: http://reprap.org/wiki/G-code#M218:_Set_Hotend_Offset Thank You CompoundCarl for ...
- Mon Nov 23, 2015 10:52 am
- Forum: Troubleshooting and Bug Reports
- Topic: badprinter2 second extruder offset
- Replies: 5
- Views: 3756
- Jump to post
badprinter2 second extruder offset
Hi all, i'm new with S3D and I didn't find a solution to my problem, in posts o tutorials... The point is: does any one of you tried the dual extrusion print using Bad Printer 2 (a marlin modified firmware)? while I've setted the offset for T1 in the Gcode Tab and the preview works fine, in the prin...
