Search found 8 matches
- Tue Sep 12, 2017 3:30 am
- Forum: Troubleshooting and Bug Reports
- Topic: Nozzle crossing top layer making scars
- Replies: 4
- Views: 3418
- Jump to post
Re: Nozzle crossing top layer making scars
Ah, thanks guys! I had forgotten to disable "Only retract when crossing open spaces".
- Fri Sep 08, 2017 8:32 am
- Forum: Troubleshooting and Bug Reports
- Topic: Nozzle crossing top layer making scars
- Replies: 4
- Views: 3418
- Jump to post
Nozzle crossing top layer making scars
I'm sure this has been discussed before, but I could not find any threads on it – so I'm sorry if this is a repeat. Now, I'm getting lines in my top layers because the nozzle is crossing over, leaving these ugly lines/scars. Is there any way to avoid this, with a z-lift on travel or similar? See exa...
- Tue Nov 01, 2016 9:09 am
- Forum: General Discussion and Tips
- Topic: Model get's "broken" when I Prepare to print
- Replies: 5
- Views: 4489
- Jump to post
Re: Model get's "broken" when I Prepare to print
Thanks for all the suggestions, guys!
I'll give "Mesh > Separate Connected Surfaces" when I get home tonight, that sounds about right.
If not, Meshmixer.
I'll give "Mesh > Separate Connected Surfaces" when I get home tonight, that sounds about right.
If not, Meshmixer.
- Mon Oct 31, 2016 5:11 pm
- Forum: General Discussion and Tips
- Topic: Model get's "broken" when I Prepare to print
- Replies: 5
- Views: 4489
- Jump to post
Model get's "broken" when I Prepare to print
Hi I have been using S3D for a while, but never had this happen before. When I click "Prepare to Print!" the model changes it's characteristics. The overlapping parts are simply removed, making the model useless. Moedeled in Fusion 360. See the pictures. https://d3vv6lp55qjaqc.cloudfront.n...
- Fri Dec 18, 2015 5:56 am
- Forum: Troubleshooting and Bug Reports
- Topic: Supports not being printed properly
- Replies: 7
- Views: 3375
- Jump to post
Re: Supports not being printed properly
Ah yes, in the end I printed only the head as that was giving me the most problems.
But again, thanks for this input – I'll give it a go with new settings.
But again, thanks for this input – I'll give it a go with new settings.
- Fri Dec 18, 2015 5:51 am
- Forum: Troubleshooting and Bug Reports
- Topic: Supports not being printed properly
- Replies: 7
- Views: 3375
- Jump to post
Re: Supports not being printed properly
Well the photo you posted isn't working either, but I'll take a guess. Your factory file only has a tiny little hook that is above the build platform that could need support. The hook is only about 2mm wide, but you currently have your support pillar size set to 5mm! There's no way a 5mm pillar wil...
- Thu Dec 17, 2015 3:29 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Supports not being printed properly
- Replies: 7
- Views: 3375
- Jump to post
Re: Supports not being printed properly
Sure, here's the factory file: http://cl.ly/2y3r061L1b2K
- Thu Dec 17, 2015 6:48 am
- Forum: Troubleshooting and Bug Reports
- Topic: Supports not being printed properly
- Replies: 7
- Views: 3375
- Jump to post
Supports not being printed properly
I have problems with supports not being printed as they should. Now, the exact same model sliced in Cura comes out perfect. So I'm wondering what I'm doing wrong in S3D? What could cause this? http://cl.ly/3w0F3M1z3R0G/Image%202015-12-18%20at%2011.50.08%20am.png http://cl.ly/3w0F3M1z3R0G/Image%20201...
