Thank you for this link, I just put the ITWorks Titan Aero Volcano which requires the MOARstruder firmware and wasn't finding happy results
So far this is better, I also was printing much too fast.Search found 7 matches
- Sat Jan 06, 2018 3:16 pm
- Forum: Feature Requests
- Topic: Lulzbot Taz 6 Moarstruder profile
- Replies: 5
- Views: 4030
- Jump to post
Re: Lulzbot Taz 6 Moarstruder profile
So far this is better, I also was printing much too fast.- Tue Aug 01, 2017 11:53 am
- Forum: General Discussion and Tips
- Topic: Toolhead Offsets not working in S3D 4.0?
- Replies: 4
- Views: 3600
- Jump to post
Re: Toolhead Offsets not working in S3D 4.0?
Good Afternoon, I did some testing and talked with support, I'm not sure what exactly I did or didn't do during my initial testing that I couldn't get the offsets to work, but I went back to 3.1.1 and it worked fine, I then went back into 4.0.0 and started fresh and I'm now printing great with just ...
- Mon Jul 31, 2017 8:59 am
- Forum: General Discussion and Tips
- Topic: Toolhead Offsets not working in S3D 4.0?
- Replies: 4
- Views: 3600
- Jump to post
Re: Toolhead Offsets not working in S3D 4.0?
I'm so glad I took the time to sit down and write this out, as mid post is when I thought to try going back to S3D 3.1.1 and low and behold the offsets work brilliantly again!
- Mon Jul 31, 2017 8:42 am
- Forum: General Discussion and Tips
- Topic: Toolhead Offsets not working in S3D 4.0?
- Replies: 4
- Views: 3600
- Jump to post
Toolhead Offsets not working in S3D 4.0?
Good Morning, I have a PowerSpec Ultra, since moving to S3D v4.0 the toolhead offsets don't seem to impact the print. The machine settings are being updated to reflect the changes I make in the profile however the firmware on this printer is not opensource and PowerSpec won't help because the tool o...
- Tue Apr 11, 2017 8:38 am
- Forum: Troubleshooting and Bug Reports
- Topic: TAZ 6 profile
- Replies: 9
- Views: 11187
- Jump to post
Re: TAZ 6 profile
Hello I've started with the default profile and I've made a few tweaks. For some reason no matter what I have the extruder temp set to the G-code only tells the printer to heat to 170* Has anyone else ran into this? I've sent a support request but I haven't yet heard back so I'm guessing this must b...
- Thu Oct 20, 2016 6:46 am
- Forum: General Discussion and Tips
- Topic: PowerSpec Ultra - Under Extrusion from layer 2 of print?
- Replies: 2
- Views: 1485
- Jump to post
Re: PowerSpec Ultra - Under Extrusion from layer 2 of print?
Thank you for the suggestion, I frequently level but I'm sure there are more steps in that article so I'll give it a read to make sure I add anything I'm missing to my routine. Last night I heated the extruded to 260c and ran about 500mm of cleaning filament through the extruder and ended up with th...
- Wed Oct 19, 2016 5:49 pm
- Forum: General Discussion and Tips
- Topic: PowerSpec Ultra - Under Extrusion from layer 2 of print?
- Replies: 2
- Views: 1485
- Jump to post
PowerSpec Ultra - Under Extrusion from layer 2 of print?
Hello, I was printing some large prints with a very high level of success for about a week after upgrading to an all metal hotend. I did a few small prints and opted to use the "Vase" print setting because I was just printing some small rings. It gave me a message that it would override so...
