Search found 11 matches

Go to advanced search

by usagi
Mon Mar 19, 2018 2:02 am
Forum: Feature Requests
Topic: Ironing
Replies: 70
Views: 42645

Re: Ironing

+1 ironing would be nice to have.
by usagi
Mon Mar 19, 2018 1:56 am
Forum: Feature Requests
Topic: First layer chamfer
Replies: 3
Views: 847

Re: First layer chamfer

I thought so, too. But there's a much better solution to elephant foots. A well leveled bed and a print surface like BuildTak or PEI. And then your Z-Height will be perfect. elephants feet are also used to adhere down corners better to help reduce warping due to differential cooling of areas with r...
by usagi
Mon Mar 19, 2018 1:31 am
Forum: Feature Requests
Topic: minimum layer time -> optional lift head and wait
Replies: 3
Views: 1309

Re: minimum layer time -> optional lift head and wait

what about the ooze from idle nozzle? 30 sec will ooze a lot.
by usagi
Mon Mar 19, 2018 1:29 am
Forum: Feature Requests
Topic: Feature request: access to pre-init gcode
Replies: 1
Views: 332

Feature request: access to pre-init gcode

I'd like to have access to pre-init gcode. Current simplify3d inserts something like this before the user init gcode: G90 M82 M106 S0 M140 S60 M190 S60 M104 S240 T0 M109 S240 T0 M221 T0 S100 In order to prevent massive oozing during initial extruder heating, i'd like to be able to do something like ...
by usagi
Wed May 25, 2016 12:15 am
Forum: General Discussion and Tips
Topic: Wavy Patterns
Replies: 4
Views: 2106

Re: Wavy Patterns

you have severe z wobble.
by usagi
Mon Apr 18, 2016 6:31 am
Forum: Feature Requests
Topic: Blip extruder temperature when turning fan on
Replies: 0
Views: 419

Blip extruder temperature when turning fan on

Need a blip temperature to go along with the blip fan on bridges.

When the fan turns on, it shocks the extuder to instantly drop 15C. This results in underextrusion and failed prints.

Would be nice to have an option to blip the extruder temperature before turning the fan on, to prevent this.
by usagi
Sat Apr 16, 2016 7:09 pm
Forum: General Discussion and Tips
Topic: Which setting to eliminate zits on this part?
Replies: 18
Views: 3064

Re: Which setting to eliminate zits on this part?

what layer height are you using? try 0.2mm
by usagi
Thu Apr 14, 2016 11:32 pm
Forum: General Discussion and Tips
Topic: Which setting to eliminate zits on this part?
Replies: 18
Views: 3064

Re: Which setting to eliminate zits on this part?

print stopping is usually due to communications issues.

try printing from SD card?
by usagi
Thu Apr 14, 2016 3:35 am
Forum: General Discussion and Tips
Topic: Which setting to eliminate zits on this part?
Replies: 18
Views: 3064

Re: Which setting to eliminate zits on this part?

Motolectric wrote:I did that and the preview still shows the some red lines going across the open area to the back walls.
increase the detour factor to 30 or 50.
by usagi
Sat Mar 12, 2016 9:16 pm
Forum: General Discussion and Tips
Topic: Which setting to cure this zipper effect
Replies: 4
Views: 1784

Re: Which setting to cure this zipper effect

those are z-scar caused by retractions and wipe. see if you can turn them both off and still get a successful print.

Go to advanced search