Search found 77 matches

Go to advanced search

by Heutinck
Fri Dec 22, 2017 9:32 am
Forum: Troubleshooting and Bug Reports
Topic: Multiprocess issues
Replies: 3
Views: 655

Re: Multiprocess issues

What happens if you turn that off for that particular process?
by Heutinck
Tue Apr 11, 2017 8:44 am
Forum: Troubleshooting and Bug Reports
Topic: Retraction Issue
Replies: 15
Views: 2330

Re: Retraction Issue

Yes that's what I thought too, but then I checked my scripts tab. this is the only line in my starting script.

G28 ; home all axes

I have no other scripts except the ending script to turn off everything.

Just thought it was interesting.
by Heutinck
Mon Apr 10, 2017 8:52 pm
Forum: Troubleshooting and Bug Reports
Topic: Retraction Issue
Replies: 15
Views: 2330

Re: Retraction Issue

Hey Brian442, Thanks for the info. never thought of that. I check and there is no retractions happening. I will have to take the hotend apart and see if there is something mechanically wrong with it. also may trend the temperatures somehow to see if the temp is dropping during the print. I found out...
by Heutinck
Sun Apr 09, 2017 3:39 pm
Forum: Troubleshooting and Bug Reports
Topic: Retraction Issue
Replies: 15
Views: 2330

Retraction Issue

Hi I've got a duplicator I3 with a microswiss all metal hotend. I have been having and issue lately where even if I turn retraction settings off in S3D, after about a cm of z height printing, there is a major retraction the retracts the filament too far and it gets stuck. It was printing beautifully...
by Heutinck
Mon Nov 07, 2016 1:04 pm
Forum: General Discussion and Tips
Topic: Getting the print off the bed
Replies: 2
Views: 621

Re: Getting the print off the bed

if you are pr9inting on a glass sheet, put it in the freezer for 5 or 10 minutes.
by Heutinck
Fri Oct 28, 2016 9:35 am
Forum: General Discussion and Tips
Topic: Continue a failed print
Replies: 7
Views: 5377

Re: Continue a failed print

Actually if you lower the part below the bed you would not use the start printing at height option or it will start at that height based on the newly slice part.
by Heutinck
Wed Oct 19, 2016 9:22 am
Forum: Troubleshooting and Bug Reports
Topic: Slicer Covering holes in
Replies: 3
Views: 548

Re: Slicer Covering holes in

more than likely there is an error in the stl file. try running it through on of the online repair services.
by Heutinck
Tue Oct 18, 2016 12:20 am
Forum: General Discussion and Tips
Topic: Multiple Raft Materials??
Replies: 2
Views: 597

Re: Multiple Raft Materials??

Have you tried using a brim instead of a raft? most parts, especially those without sharp 90 degree corners don't actually need a raft.
by Heutinck
Tue Oct 18, 2016 12:15 am
Forum: General Discussion and Tips
Topic: Tip on wanhao i3 Flexi filament
Replies: 2
Views: 690

Re: Tip on wanhao i3 Flexi filament

probably could have just used this. http://www.thingiverse.com/thing:981106
by Heutinck
Tue Oct 18, 2016 12:07 am
Forum: General Discussion and Tips
Topic: Different Settings for Different Regions of a Model
Replies: 10
Views: 1735

Re: Different Settings for Different Regions of a Model

are you printing the whole spherical section with high infill? You probably should only print the bottom half of the spherical portion at 100% infill like Doug suggested. If you print the whole spherical portion with high infill, then that section wouldn't care what orientation it was in, so the top...

Go to advanced search