Search found 1100 matches

Go to advanced search

by wirlybird
Thu May 23, 2019 1:37 pm
Forum: Troubleshooting and Bug Reports
Topic: Slicing errors
Replies: 3
Views: 19

Re: Slicing errors

Considering that this is happening at most of the intersections I think you have issue with the model such as flipped faces or something like that. I would run the model through a fixer like Netfabb or makeprintable.com to see what it says. Also in S3D go to the mesh menu and try the separate connec...
by wirlybird
Thu May 23, 2019 12:50 pm
Forum: Troubleshooting and Bug Reports
Topic: Support area wwoun't be neat
Replies: 4
Views: 39

Re: Support area wwoun't be neat

Thank you for your reply. I tried to decrease the temperature from 195 to 190 and to 185. No change. Then I added 4 layers dense support 100%. No significant change. At temp 200 and printing two objects, the result was a bit better (at the filleted edge), but still not good enough. Regarding dense ...
by wirlybird
Thu May 23, 2019 5:54 am
Forum: Troubleshooting and Bug Reports
Topic: New Version not printing at all
Replies: 1
Views: 28

Re: New Version not printing at all

This really seems more like an issue you should be directing at a forum or Facebook group for the printer or even the manufacturers support for help. Most likely not a slicer (S3D) issue. Maybe someone on here will be able to offer something but I wouldn't count on it. Only thing I can offer is this...
by wirlybird
Wed May 22, 2019 11:38 am
Forum: Troubleshooting and Bug Reports
Topic: Support area wwoun't be neat
Replies: 4
Views: 39

Re: Support area wwoun't be neat

As can be seen on the picture, the lower site of this curved model is horrible as is the filleted edge at the same level. I tried many different settings without succes. The test model here is part of a bigger model. That's why it is oriented as is.) I very much appreciate any help. Best regards, N...
by wirlybird
Wed May 22, 2019 9:24 am
Forum: General Discussion and Tips
Topic: Fusion3 F410
Replies: 0
Views: 32

Fusion3 F410

Hi all,

Anyone running a Fusin3 F410 printer? Just wondering how it is going and your impressions of it and with S3D.

Thanks.
by wirlybird
Wed May 22, 2019 9:22 am
Forum: Troubleshooting and Bug Reports
Topic: Small outcroppings are overextruded
Replies: 5
Views: 81

Re: Small outcroppings are overextruded

I've attached the factory file. The material is Hatchbox Silver PLA at 170C going 40mm/s or 2400mm/min. I suspected temperature as well and have tried 210, 200, 190, 180. Most people seem to recommend 210-200 for this filament but I didn't have any luck with those. Temps are ok. On Hatchbox you pro...
by wirlybird
Wed May 22, 2019 9:16 am
Forum: General Discussion and Tips
Topic: Different ways to make rafts?
Replies: 1
Views: 225

Re: Different ways to make rafts?

Off topic but how do you like the 410?
I am considering getting one.
by wirlybird
Mon May 20, 2019 10:19 am
Forum: Troubleshooting and Bug Reports
Topic: Small outcroppings are overextruded
Replies: 5
Views: 81

Re: Small outcroppings are overextruded

I've minimized my over extrusion and the rest of my prints are coming out fine. But whenever I have a small island all by itself, I seem to get a lot of printing issues. Are there any settings in Simplify3D that could improve this? Here are some examples of what I'm talking about. Notice the blobs ...
by wirlybird
Thu May 16, 2019 6:46 am
Forum: General Discussion and Tips
Topic: Anyone Using a Sigmax R19 & S3D?
Replies: 0
Views: 41

Anyone Using a Sigmax R19 & S3D?

I am ordering this printer and wondered who may be using one with S3D.

What has your experience been?
by wirlybird
Wed May 15, 2019 12:09 pm
Forum: Feature Requests
Topic: No Bottom Dense Support Layer
Replies: 6
Views: 124

Re: No Bottom Dense Support Layer

Thanks for this excellent feature request. Were you thinking this would be an option to change the number of bottom vs top dense support layers or just an option to remove bottom dense layers entirely? Either would be ok but if you did it as a selectable number of layers for each top and bottom sep...

Go to advanced search