Search found 33 matches

Go to advanced search

by mroschk
Wed Nov 06, 2019 1:21 pm
Forum: Troubleshooting and Bug Reports
Topic: Printer goes to left in the middle of the print
Replies: 0
Views: 384

Printer goes to left in the middle of the print

Hello, i have a strange problem. When i print some models, which are around 2-3cm high, the printer starts very nice. But then , anywhen in the middle of the print, the printer stops, goes to the left, comes back to the model and continue working. Sometimes the print is usable, but sometimes the pri...
by mroschk
Thu Apr 25, 2019 5:22 pm
Forum: Troubleshooting and Bug Reports
Topic: Question about print sequence
Replies: 7
Views: 805

Re: Question about print sequence

Hello,

thanks, i will try.
But i added the factory file here, maybe tere is also anything else wrong.

Matthias
by mroschk
Wed Apr 24, 2019 4:16 pm
Forum: Troubleshooting and Bug Reports
Topic: Question about print sequence
Replies: 7
Views: 805

Re: Question about print sequence

hmm, for sure, but it is always to hard to remove the Support. so i dont want that
by mroschk
Wed Apr 24, 2019 2:49 pm
Forum: Troubleshooting and Bug Reports
Topic: Question about print sequence
Replies: 7
Views: 805

Question about print sequence

Hello,

i have attached a STL File and the problem is at Line 32167.
Here you can see he prints first a layer in the middle and without any hold the layer starts in the Air and
falls down for sure.
Is there any setting to say the printer to start such things from outside to inside ?

Thanks
Matthias
by mroschk
Tue Nov 29, 2016 12:38 pm
Forum: General Discussion and Tips
Topic: Why is it not full filled?
Replies: 13
Views: 4896

Re: Why is it not full filled?

Hello,

Thanks for the Links Horst...i think that helps...a lot to read but seams to explain all.
I will also try the horizontal size compenstaion...

Thanks
Matthias
by mroschk
Tue Nov 29, 2016 10:08 am
Forum: General Discussion and Tips
Topic: Why is it not full filled?
Replies: 13
Views: 4896

Re: Why is it not full filled?

Hello, i finished the print (without any stop :) ) and you can see the result in the attachment. The top is now closed, ok, but anything is wrong with the Support. I am not able to remove the Support, it is directly connected with the normal material. Also the Messures are not correct. It should be ...
by mroschk
Mon Nov 28, 2016 5:11 pm
Forum: General Discussion and Tips
Topic: Why is it not full filled?
Replies: 13
Views: 4896

Re: Why is it not full filled?

Ahh...over there...i am so sorry...

I try it tomorrow and come back with a Report .. Thanks

Matthias
by mroschk
Mon Nov 28, 2016 4:48 pm
Forum: General Discussion and Tips
Topic: Why is it not full filled?
Replies: 13
Views: 4896

Re: Why is it not full filled?

Hello,

ok, i will do that ( but tomorrow :-) )...but i dont understand the second part:
Thin Wall Behavior to Gap fill at 50%
What must i here do and where ? I search for a "GAP Fill " Settig, but did not find that.

Sorry...i am a bit new in S3D

Matthias
by mroschk
Mon Nov 28, 2016 1:36 pm
Forum: General Discussion and Tips
Topic: Why is it not full filled?
Replies: 13
Views: 4896

Re: Why is it not full filled?

Hello,

i changed the "Extrusion Multiplier" back to 1.0.
Now it seams to work. Maybe that was the reason.

Matthias
by mroschk
Mon Nov 28, 2016 1:35 pm
Forum: General Discussion and Tips
Topic: Printer Stops sometimes
Replies: 9
Views: 1673

Re: Printer Stops sometimes

Hello, thats good :-) Today the Printer stops again in the iddle of a print which was printed before without any stop. So i was a bit frustrated and tuck the SD Card out and put it in again...and then the Printer resume to print. Strange...isnt it ? So it seams the Problem is the SD Card Reader or m...

Go to advanced search