Search found 8 matches
- Mon Jun 15, 2020 2:58 pm
- Forum: Troubleshooting and Bug Reports
- Topic: dual extruder not respecting offset
- Replies: 10
- Views: 3852
- Jump to post
Re: dual extruder not respecting offset
So it looks like the X offset is gone now. There is nothing in your previous files that shows there should be a Y offset. Can you post an updated Factory File just so I can verify this? If there is indeed no Y offset set there then this would seem to be a Firmware or hardware issue. Have you upgrad...
- Fri Jun 05, 2020 2:07 pm
- Forum: Troubleshooting and Bug Reports
- Topic: dual extruder not respecting offset
- Replies: 10
- Views: 3852
- Jump to post
Re: dual extruder not respecting offset
tried fresh... here's the factory file and the results of the print..
- Thu Jun 04, 2020 10:50 am
- Forum: Troubleshooting and Bug Reports
- Topic: dual extruder not respecting offset
- Replies: 10
- Views: 3852
- Jump to post
Re: dual extruder not respecting offset
yeah sorry that was before i unchecked it i realized. It is unchecked (and I've tried with it checked).
Also after my failed road cone, I uploaded the previous successful print, and getting the same issues now.
Also after my failed road cone, I uploaded the previous successful print, and getting the same issues now.
- Wed Jun 03, 2020 6:40 pm
- Forum: Troubleshooting and Bug Reports
- Topic: dual extruder not respecting offset
- Replies: 10
- Views: 3852
- Jump to post
Re: dual extruder not respecting offset
sorry for the delay, was waiting on some new hotend nozzles and have been trying to re-setup the printer. After getting everything reset, I was able to succesully print a calibration print.. then I went to try the roadcone print.. and it did exactly the same thing as before.. no settings changed. I'...
- Tue May 26, 2020 12:16 pm
- Forum: Troubleshooting and Bug Reports
- Topic: dual extruder not respecting offset
- Replies: 10
- Views: 3852
- Jump to post
Re: dual extruder not respecting offset
Have you set offsets for both hot ends? You only need to set the offset for one tool. T0 should be considered the base to reference from, T1 should have an offset from T0, if you have T0 with an offset as well this can cause this issue. Check in Preferances>Machine Toolhead offsets. Yeah I did chec...
- Mon May 18, 2020 1:32 pm
- Forum: Troubleshooting and Bug Reports
- Topic: dual extruder not respecting offset
- Replies: 10
- Views: 3852
- Jump to post
dual extruder not respecting offset
Okay guys, this is a new one and i've scoured google as well as I feel I can, hit a couple of different places and not turning anything up. I've had S3d for a couple of years and fairly happy with how well it performs. Just recently I've gone through the efforts of repairing my second extruder and s...
- Fri Nov 11, 2016 10:50 pm
- Forum: General Discussion and Tips
- Topic: FlashForge Stringing after nozzle upgrade
- Replies: 2
- Views: 1783
- Jump to post
Re: FlashForge Stringing after nozzle upgrade
Thanks for the input, i'll try playing w/ coasting and see if that affects anything.
- Wed Nov 09, 2016 8:22 pm
- Forum: General Discussion and Tips
- Topic: FlashForge Stringing after nozzle upgrade
- Replies: 2
- Views: 1783
- Jump to post
FlashForge Stringing after nozzle upgrade
I'm encountering a new problem after swapping out to new nozzles. Now ALL of my prints where there is any jump between open space i get a perfect line between these points. (the same lines you can see in the S3D software labeled 'travel moves') no matter what settings I change I am unable to make AN...
