Search found 24 matches

Go to advanced search

by pascal32
Wed Feb 08, 2017 8:55 pm
Forum: General Discussion and Tips
Topic: seam printing with clear colorfabb xt
Replies: 9
Views: 2437

Re: seam printing with clear colorfabb xt

those are some good suggestions, I'll give them a try. the printing two - I should be able to too a pillar or shield for the same effect.

thanks!
by pascal32
Mon Feb 06, 2017 7:53 pm
Forum: General Discussion and Tips
Topic: seam printing with clear colorfabb xt
Replies: 9
Views: 2437

Re: seam printing with clear colorfabb xt

suggestion on how to tune this a bit so i can get the seam cleaned up without sacrificing the other areas? Vase mode won't work for the end product which is a small container. on a side note it does print nicely in vase mode, the issue is stopping and layer changing. thanks! https://forum.simplify3d...
by pascal32
Sat Feb 04, 2017 6:57 pm
Forum: General Discussion and Tips
Topic: seam printing with clear colorfabb xt
Replies: 9
Views: 2437

Re: seam printing with clear colorfabb xt

one more picture
by pascal32
Sat Feb 04, 2017 6:56 pm
Forum: General Discussion and Tips
Topic: seam printing with clear colorfabb xt
Replies: 9
Views: 2437

seam printing with clear colorfabb xt

Hi there. I've been trying to print a cylinder with colorfabb xt petg. Initial prints were pretty rough. I was able to get the quality better, however I had to use an extra restart distance of -.35 and a coast of .10. Using wipe just spread the issue all over. this is causing what I suspect is under...
by pascal32
Sun Jan 22, 2017 9:53 am
Forum: General Discussion and Tips
Topic: Why do not I can do a better setting
Replies: 12
Views: 5531

Re: Why do not I can do a better setting

I'm not sure if there is a way to transfer, I doubt it though. I did read the extrusion multiplier is reversed in some programs, so even if you manually move everything over one program might read the value differently than another resulting in print quality differences.
by pascal32
Sun Jan 22, 2017 9:50 am
Forum: General Discussion and Tips
Topic: what the heck happened, left printer head behaves different
Replies: 5
Views: 2614

Re: what the heck happened, left printer head behaves differ

thank you, I missed that section, some good info in there!
by pascal32
Sun Jan 22, 2017 9:48 am
Forum: General Discussion and Tips
Topic: print items one at a time
Replies: 6
Views: 11495

Re: print items one at a time

I have never tried it, the option appears when you click "prepare to print" after configuring your print - the dialog which appears has a radio button for selecting sequential printing.
by pascal32
Sat Jan 21, 2017 10:09 pm
Forum: General Discussion and Tips
Topic: dual extrusion with different material
Replies: 2
Views: 1956

dual extrusion with different material

I'm trying to print with PLA on the left head and PolyFlex on the right. I have profile for each which is working well. After some tries with the wizard I went manual, but the results aren't as good for the PolyFlex as they are standalone. its like the retraction and extrusion multiplier aren't work...
by pascal32
Sat Jan 21, 2017 5:26 pm
Forum: General Discussion and Tips
Topic: what the heck happened, left printer head behaves different
Replies: 5
Views: 2614

Re: what the heck happened, left printer head behaves differ

I just did an eprom erase and that fixed it. Thinking I screwed things up running the dual extruder alignment script. Now to figure out how to align the two extruders in FW (off just a hair)

Go to advanced search