Search found 9 matches

Go to advanced search

by cmarko
Fri May 24, 2019 7:21 am
Forum: Troubleshooting and Bug Reports
Topic: Crashing, saving profiles, closing profile window, saving factory files, etc.
Replies: 6
Views: 624

Re: Crashing, saving profiles, closing profile window, saving factory files, etc.

Hi cmarko, What you have is likely a corrupted profile (FFF) that is 'infecting' the others. Go through your saved profiles and try to export each one in turn. If a profile is badly corrupted, it will crash S3D. After you restart, just delete the one that crashed. Do NOT load or try to use any furt...
by cmarko
Thu May 09, 2019 8:37 pm
Forum: Troubleshooting and Bug Reports
Topic: Crashing, saving profiles, closing profile window, saving factory files, etc.
Replies: 6
Views: 624

Re: Crashing, saving profiles, closing profile window, saving factory files, etc.

dkightley wrote:
Thu May 09, 2019 4:26 pm
Have a read of this thread: viewtopic.php?f=9&t=12998&p=49941&hilit ... ers#p49941

Doesn't apply to my problem with crashing. I do not use accent characters.
by cmarko
Thu May 09, 2019 11:24 am
Forum: Troubleshooting and Bug Reports
Topic: Crashing, saving profiles, closing profile window, saving factory files, etc.
Replies: 6
Views: 624

Crashing, saving profiles, closing profile window, saving factory files, etc.

My copy of simplify3d has been crashing with increasing frequency. I can not reliably save any settings and in many cases slicing models will result in a crash as well. This has been happening for a couple months, in that time I've read most of the troubleshooting in the bug reports regarding crashe...
by cmarko
Tue Feb 05, 2019 11:14 am
Forum: General Discussion and Tips
Topic: Smoothieware
Replies: 1
Views: 497

Re: Smoothieware

Yes, it works fine with smoothieware. Here's the gcode tab settings that are compatible with smoothieware.
Smoothieware Gcode Tab.JPG
by cmarko
Mon Mar 19, 2018 12:08 pm
Forum: Troubleshooting and Bug Reports
Topic: [FIXED] Freeze for few seconds middle of printing
Replies: 29
Views: 10744

Re: Freeze for few seconds middle of printing

The majority of this problem is caused by a feed rate of zero. I don't know what causes it but I have plenty of files that have to be tweaked in order to slice correctly. G1 E0.0000 F1200 G92 E0 G92 E0 G1 X-29.501 Y-41.776 E-2.5000 F0 G1 Z1.620 F9000 G1 X-34.040 Y-51.491 F9000 G1 Z1.420 F9000 G1 E0....
by cmarko
Mon Sep 25, 2017 9:30 am
Forum: Feature Requests
Topic: Minimum Layer Time
Replies: 2
Views: 2517

Minimum Layer Time

"Minimum layer time" to replace "Adjust printing speed for layers below" and eliminate the "allow speed reductions down to" setting. To prevent warp and overheated parts the Speed Override for "Adjust printing speed for layers below" is a helpful setting. This setting adequately addresses some of t...
by cmarko
Mon Jan 16, 2017 2:09 pm
Forum: Troubleshooting and Bug Reports
Topic: Long Delays Before Print?
Replies: 5
Views: 1551

Re: Long Delays Before Print?

Long pre-heat cycles can have more than one cause. Make sure temperature sensor in contact with the print bed. Double check the connections between the controller and the heated bed. If a terminal is not screwed down securely on a bare wire it could reduce the current going to the heated platform. T...
by cmarko
Mon Jan 16, 2017 1:41 pm
Forum: Troubleshooting and Bug Reports
Topic: How to slow down first layer skirt speed?
Replies: 10
Views: 4324

Re: How to slow down first layer skirt speed?

This would do the exact same thing as modifying the "first layer speed" setting. They both change the speed of the entire first layer, so I'm not sure why you wouldn't just use the option already in S3D?? My default profile has no brim and it uses the speed reduction in the "first layer speed" sett...
by cmarko
Sun Jan 15, 2017 1:57 pm
Forum: Troubleshooting and Bug Reports
Topic: How to slow down first layer skirt speed?
Replies: 10
Views: 4324

Re: How to slow down first layer skirt speed?

Have the same issue. I tried to trick it with Two separate Processes in one of them printer's Infill supports speed is set to desired speed Chekhov has a good dialog driven solution. Below is an alternate solution if you prefer to use a single profile for printing. Solution: If you are using marlin...

Go to advanced search