Search found 8 matches
- Sun Apr 09, 2017 1:19 am
- Forum: General Discussion and Tips
- Topic: stutter on skirt and skirt only
- Replies: 1
- Views: 1089
- Jump to post
stutter on skirt and skirt only
In simplify 3d, i try to use a skirt on every print other wise my extruder can't get enough out right away. However in only Simplify 3d, my delta printer stutters about every mm. This only happens on the skirt. I have tried repetier and it does not do this as simplify does. Suggestions>
- Sun Apr 09, 2017 1:14 am
- Forum: Troubleshooting and Bug Reports
- Topic: Delta printer pauses
- Replies: 11
- Views: 6096
- Jump to post
Re: Delta printer pauses
I have managed to figure it out after lots of trials. I changed the g code flavour in repetier to reprap volumetric and it worked, but I wanted to used simplify and simplify does not have that flavour. In the end I don't think it was the communication or flavour(even though that worked). Since I am ...
- Tue Mar 21, 2017 8:18 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Delta printer pauses
- Replies: 11
- Views: 6096
- Jump to post
Re: Delta printer pauses
[quote][/quote]
The segmentation also did not work, i also tried cura and slicer, both with no results. Do you think a broken ramps board would exibit this behavior, i already replaced arduino and that is not the problem. G code clean up software?
The segmentation also did not work, i also tried cura and slicer, both with no results. Do you think a broken ramps board would exibit this behavior, i already replaced arduino and that is not the problem. G code clean up software?
- Tue Mar 21, 2017 1:39 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Delta printer pauses
- Replies: 11
- Views: 6096
- Jump to post
Re: Delta printer pauses
No the extruder does not turn in reveres, i have also played around with settings in slicer, but if retraction is not enabled in the firmware, wouldn't it not be able to work.
- Tue Mar 21, 2017 1:13 am
- Forum: Troubleshooting and Bug Reports
- Topic: Delta printer pauses
- Replies: 11
- Views: 6096
- Jump to post
Re: Delta printer pauses
May anyone please help me. I have heard Simplify 3d has great customer service, but am not receiving it.
I have also heard some stuff about g code clean up. The ones out their that I have seen are only for kisslicer.
I have also heard some stuff about g code clean up. The ones out their that I have seen are only for kisslicer.
- Thu Mar 16, 2017 12:50 am
- Forum: Troubleshooting and Bug Reports
- Topic: Delta printer pauses
- Replies: 11
- Views: 6096
- Jump to post
Re: Delta printer pauses
I have downloaded several different types of code and they all do the same thing I have messed with buffer and cache and print line size all with no luck could it be my arduino?
- Tue Mar 14, 2017 2:44 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Delta printer pauses
- Replies: 11
- Views: 6096
- Jump to post
Re: Delta printer pauses
I have reviewed the G code and did not find any errors nor any anomalies in its commands. I have also tried printing over SD but it still does the same thing.
- Sun Mar 12, 2017 10:03 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Delta printer pauses
- Replies: 11
- Views: 6096
- Jump to post
Delta printer pauses
I have a delta printer that I am running using repetier firmware. However I have gotten everything calibrated and a new problem has surfaced. When I print a part, the printer will pause about every 2 seconds or only a brief time. This causes blobs ect. I have experimented with changing Baud rates, b...
