Search found 13 matches

Go to advanced search

by munchit1
Sun Sep 03, 2017 8:39 am
Forum: General Discussion and Tips
Topic: Z-height problem
Replies: 0
Views: 952

Z-height problem

Hi all, again. having trouble setting the height on the bed printing, basicaly the nozle keeps starting too high above the bed and will not lower no how.. the nozzle homes to a leval 0.25mm, the width of the paper...layer height 0.3mm with a 0.4mm nozzle (tried down to 0.2mm). to my reconing lowerin...
by munchit1
Sat Aug 05, 2017 8:57 am
Forum: Troubleshooting and Bug Reports
Topic: Temperature never reachs
Replies: 2
Views: 456

Temperature never reachs

hi all, on repetier host the nozzle temperature reach's it' set temp, in simply 3d it always settles between 1 or 2 degree's short and never starts the print. is there an adjustment for the temperature readings at all? or how do i sort this out? it's a Melzi 2 V3 tronxy board running repetier 9.1 (n...
by munchit1
Fri Mar 31, 2017 7:39 pm
Forum: Troubleshooting and Bug Reports
Topic: bridge speed multiplier
Replies: 1
Views: 926

Re: bridge speed multiplier

faize 2 and n0 two 1kilo spool later.


ok..why wont the multiplier work?

i'm at 2% of 60 aparently equals 40mm/s...
by munchit1
Fri Mar 31, 2017 4:32 pm
Forum: Troubleshooting and Bug Reports
Topic: bridge speed multiplier
Replies: 1
Views: 926

bridge speed multiplier

if i set the bridge speed multiplier to 10 percent does it lower the speed that it bridges accross the gap?

edit, i'll refraize that to should it lower the speed?
by munchit1
Wed Mar 29, 2017 7:17 pm
Forum: General Discussion and Tips
Topic: settings
Replies: 0
Views: 446

settings

hi all, i'm near on giving this up as a bad job here.. basic question, do you have to recalibrate for dimentions everytime you do a new model? i'm literaly chaising my tail here, 1 kilo of test prints to calibrate later i have nothing to show. set the steps per mm in marlin, do a print its ok, set u...
by munchit1
Tue Mar 28, 2017 6:43 pm
Forum: Troubleshooting and Bug Reports
Topic: the fun begins...
Replies: 5
Views: 927

Re: the fun begins...

found 1 issue, running 64bit win10 to marlin on 16 or 32bit controler boards. had help on that but run as administrator and set the program to run 'as win7'..cleared some issues up. regaurding the top/bottom infill, (not the infill e.g. honeycomb infill bit) printing more layers only water tights at...
by munchit1
Tue Mar 28, 2017 4:00 pm
Forum: Troubleshooting and Bug Reports
Topic: the fun begins...
Replies: 5
Views: 927

Re: the fun begins...

Thank you for the reply.

i'll try a fresh install on the printer and simplyfi and see how that does.

and of course re calibrate from scrach.
by munchit1
Tue Mar 28, 2017 10:42 am
Forum: Troubleshooting and Bug Reports
Topic: the fun begins...
Replies: 5
Views: 927

Re: the fun begins...

ahhh verticle lift, thank you for that. A. Set the speeds. visualy you see how fast its printing the plastik, on the image attached first box is set to 40mm/s, tisnt that fast when you've had succesfull 120mm/s print speeds, well every now and then it'll print at some very very fast rate for no reas...
by munchit1
Mon Mar 27, 2017 8:34 pm
Forum: Troubleshooting and Bug Reports
Topic: the fun begins...
Replies: 5
Views: 927

the fun begins...

hi all..got some weird things going on. A. set the speed to 45mm/s result, aything from 45 and some where in the region of 80 - 85mm/s randomly happens.(then doesnt then does.) B. no matter what infill thickness i set it remains the same. (i gave up at 200%) cannot get a water tight top or bottom la...
by munchit1
Fri Mar 24, 2017 9:51 pm
Forum: Troubleshooting and Bug Reports
Topic: print begins withour reaching temperatures
Replies: 5
Views: 1981

Re: print begins withour reaching temperatures

and a thank you to the people who made this program, i've spend four weeks going through every program i could find, and all had at least one thing rong that made it useless, but most of all i couldnt use any to print from a pc, silly things like printing some wird squigldy print some where else on ...

Go to advanced search