Search found 10 matches

Go to advanced search

by Juliemac
Sat Aug 26, 2023 11:23 am
Forum: Troubleshooting and Bug Reports
Topic: Printing height problem
Replies: 2
Views: 565
 
Jump to post

Re: Printing height problem

Advanced tab on the process settings page. Custom height button on the lower left.
by Juliemac
Fri Aug 25, 2023 10:47 pm
Forum: Troubleshooting and Bug Reports
Topic: Printing height problem
Replies: 2
Views: 565
 
Jump to post

Printing height problem

Version 5.1
I drop an object on the deck and I see a blue rectangle on the deck that is 3mm thick.
If I try to get it ready for printing, the height only goes up to the height of the rectangle.

How can I clear this?
by Juliemac
Mon Oct 17, 2022 8:48 am
Forum: General Discussion and Tips
Topic: Using the Variable Settings Wizard to section out a print
Replies: 3
Views: 843
 
Jump to post

Re: Using the Variable Settings Wizard to section out a print

That did it! Perfect.
Many thanks guys!
by Juliemac
Sat Oct 15, 2022 8:02 am
Forum: General Discussion and Tips
Topic: Using the Variable Settings Wizard to section out a print
Replies: 3
Views: 843
 
Jump to post

Using the Variable Settings Wizard to section out a print

I'm hoping the Variable Settings wizard can help me here. I have an object I want to print that's 30 mm tall. But. I only want to print the top 20mm. If I split the object at the 1cm mark, how do I: 1) reset the Z height to base print level 2) Print a base layer 3) Start printing at the 20mm mark at...
by Juliemac
Sat Oct 01, 2022 9:29 am
Forum: General Discussion and Tips
Topic: Mid print filament change
Replies: 0
Views: 1090
 
Jump to post

Mid print filament change

I started a very long print (4500+ minutes), but now I see I will run out of filament before it is done. The printer is a Creality Ender 3 S1 plus, being fed Gcode via USB. Looking at videos, I saw the variable setting wizard. 1) look at the Gcode stream and find the Z height as well as the X&Y ...
by Juliemac
Sun Aug 14, 2022 6:57 pm
Forum: Feature Requests
Topic: [ADDED] Creality Ender 3 S1 support
Replies: 3
Views: 2057
 
Jump to post

Re: CReality Ender 3 S1 support

I would also like it added for my machine.
by Juliemac
Wed Jan 02, 2019 9:35 pm
Forum: Troubleshooting and Bug Reports
Topic: Communications wait command
Replies: 1
Views: 822
 
Jump to post

Communications wait command

My printer does not use the command.
I have to reset that feature with each part I make. Is it possible to set the check box OFF when the software loads so I dont have to go to options/communications?

TIA!
by Juliemac
Fri Dec 15, 2017 12:51 pm
Forum: Troubleshooting and Bug Reports
Topic: Wait check box before print
Replies: 1
Views: 2455
 
Jump to post

Wait check box before print

My printer does not use the WAIT command. Each time I load an obect, I have to go to the FFF properties, click the communications tab, and uncheck the WAIT command.
Is there a setting that disables this checkbox or set it to "off"?
by Juliemac
Sat Apr 01, 2017 11:47 am
Forum: Troubleshooting and Bug Reports
Topic: Slice error
Replies: 1
Views: 946
 
Jump to post

Slice error

I am trying to print a test cube I got from Thingiverse.
It looks good and sits flat on the "floor" when I set up the FFF, but..
When I slice it, it shows the top part of the cube about 4mm above the bed. and yes, thats where it starts printing.
Nay ideas guys?

Go to advanced search