Search found 26 matches

Go to advanced search

by darKing
Sat Sep 23, 2017 9:52 am
Forum: General Discussion and Tips
Topic: question regarding "Wait for temp. controller to stabilise"
Replies: 4
Views: 1732

Re: question regarding "Wait for temp. controller to stabili

Take a look under the "scripts" tab and "starting script" there should be something like this: [...] G1 X-10 Y-10 F6000 ; Move to wait position M7 ; Wait for bed to stabilize M6 T0 ; Wait for right extruder to reach target temp <-------------- G1 X-70 Y-70 F6000 ; Move to front left corner of bed G1...
by darKing
Thu Sep 21, 2017 6:11 pm
Forum: General Discussion and Tips
Topic: V4 New Features - Video Series
Replies: 5
Views: 1107

Re: V4 New Features - Video Series

Good job mate. Thanks for putting the time and effort into this.
by darKing
Thu Sep 21, 2017 4:40 am
Forum: General Discussion and Tips
Topic: How accurate do you think S3D cost estimate is?
Replies: 5
Views: 1505

Re: How accurate do you think S3D cost estimate is?

Why not use the search when you're sure it has been asked a million times? :mrgreen: 8-) If you have density, diameter and price, it should be pretty close. (closer than the estimated time I guess). Just do some prints and weight them? If it is off by a few grams, it does not change the price signif...
by darKing
Wed Sep 20, 2017 10:15 am
Forum: General Discussion and Tips
Topic: Stringing Problem
Replies: 4
Views: 1786

Re: Stringing Problem

Are you sure those are only strings? https://www.simplify3d.com/support/print-quality-troubleshooting/#stringing-or-oozing Those marks on the right side also looks like nozzle scratches to me. https://www.simplify3d.com/support/print-quality-troubleshooting/#scars-on-top-surface Do you have a direct...
by darKing
Mon Sep 18, 2017 11:53 am
Forum: General Discussion and Tips
Topic: Found a "less than ten times the support material" approach
Replies: 2
Views: 1253

Re: Found a "less than ten times the support material" appro

Then Support will print in mid air. Great Idea! :D :roll:
by darKing
Mon Sep 18, 2017 5:59 am
Forum: General Discussion and Tips
Topic: rafts on supports
Replies: 6
Views: 2342

Re: rafts on supports

Try the "Solid base layers" in Supports Tab. You can also add Rafts to your Support but I don't know if you can add Rafts only to supports, but I'd try the solid baser layers first.
by darKing
Wed Sep 13, 2017 6:14 pm
Forum: General Discussion and Tips
Topic: Extrusion multiplier and weight of final part
Replies: 7
Views: 3347

Re: Extrusion multiplier and weight of final part

Well, considering that an extrusion Ratio of 1 isn't always the right amount (over / underextrusion), that density and weight differs depending on Filaments... it seems like a pretty strange Idea... especially if precision is what you want to achive. If you want to achive a 90 / 60 / 90 body it's ve...
by darKing
Wed Sep 13, 2017 7:20 am
Forum: General Discussion and Tips
Topic: Extrusion multiplier and weight of final part
Replies: 7
Views: 3347

Re: Extrusion multiplier and weight of final part

Have you tried weighing a part to see if it is even close the the slicers estimate, which is what it is, an estimate? The amount of filament used is a calculation so I imagine if you change the extrusion multiplier the calculation could change. It might be workable but I think the value given by th...
by darKing
Wed Sep 13, 2017 5:41 am
Forum: General Discussion and Tips
Topic: Extrusion multiplier and weight of final part
Replies: 7
Views: 3347

Re: Extrusion multiplier and weight of final part

Why not take a look at the part and then decide if it's good or not?
by darKing
Tue Sep 05, 2017 9:14 am
Forum: General Discussion and Tips
Topic: litophane killed my printer
Replies: 6
Views: 2240

Re: litophane killed my printer

Dr. Dre killed my bike! I was biking trough the night, with sunglasses on and headphones plugged into my ears. I did this all the time and always survived. This time I listened to Dr. Dre and got hit by a car. Definitely it has something to do with the track I was listening to! :o :mrgreen: :mrgreen...

Go to advanced search