Search found 11 matches

Go to advanced search

by smeek
Mon Apr 16, 2018 11:56 am
Forum: General Discussion and Tips
Topic: Post Processing Anet A8
Replies: 13
Views: 2839

Re: Post Processing Anet A8

Thanks for that. That explains a lot. Guess it is time to reflash my board. Or using the M400 and G4 seems to be working as long as I run it from the SD card.
by smeek
Sat Apr 14, 2018 5:50 pm
Forum: General Discussion and Tips
Topic: Post Processing Anet A8
Replies: 13
Views: 2839

Re: Post Processing Anet A8

M600 does not work either. Thanks
by smeek
Fri Apr 13, 2018 7:54 am
Forum: General Discussion and Tips
Topic: Post Processing Anet A8
Replies: 13
Views: 2839

Re: Post Processing Anet A8

Thanks for reply, I have been checking RepRap forum for replies to my post but none there so far. http://forums.reprap.org/read.php?406,818355 Here is what I have come up with so far. I have been running test prints with no filament using this in the post process window: {REPLACE "; layer 3," "G91 \...
by smeek
Thu Apr 12, 2018 10:14 pm
Forum: General Discussion and Tips
Topic: Post Processing Anet A8
Replies: 13
Views: 2839

Re: Post Processing Anet A8

Use M226 ; for resume it waits for a pressure on the display's button. http://reprap.org/wiki/G-code#M226:_Gcode_Initiated_Pause http://reprap.org/wiki/G-code#M226:_Wait_for_pin_state Thanks for your reply. I have already tried M226 and it does not work. I have also read the wiki's. I have saved gc...
by smeek
Thu Apr 12, 2018 11:33 am
Forum: General Discussion and Tips
Topic: Post Processing Anet A8
Replies: 13
Views: 2839

Re: Post Processing Anet A8

I'm using this code for stop and continue: {REPLACE "; layer 37," "G91 \nG1 Z10 \nG90 \nG1 X0 Y200 \nM0 Click To Restart \nG91 \nG1Z-10 \nG90 \n; layer 37,"} Thanks, I'll give that a try. I know its been a while but I am getting back to this now. This code works except for the pause. It does everyt...
by smeek
Fri Jun 09, 2017 1:37 pm
Forum: General Discussion and Tips
Topic: Post Processing Anet A8
Replies: 13
Views: 2839

Re: Post Processing Anet A8

brian442 wrote:Also, you can read about what the post-processing commands do here:
viewtopic.php?f=8&t=1959

Thanks, I have read that. Good info....
by smeek
Fri Jun 09, 2017 1:37 pm
Forum: General Discussion and Tips
Topic: Post Processing Anet A8
Replies: 13
Views: 2839

Re: Post Processing Anet A8

MasterFX wrote:I'm using this code for stop and continue:

Code: Select all

{REPLACE "; layer 37," "G91 \nG1 Z10 \nG90 \nG1 X0 Y200 \nM0 Click To Restart \nG91 \nG1Z-10 \nG90 \n; layer 37,"}

Thanks, I'll give that a try.
by smeek
Thu Jun 08, 2017 9:16 am
Forum: General Discussion and Tips
Topic: Post Processing Anet A8
Replies: 13
Views: 2839

Post Processing Anet A8

Hello, I found the following code on youtube. It is to allow for changing the filament color at a selected layer. It seems to work for the most part except the first thing it does is raise the Z height by 5 cm and when it comes back to print the Z height does not come back down to the original heigh...
by smeek
Fri May 19, 2017 12:31 pm
Forum: General Discussion and Tips
Topic: Skynet Firmware
Replies: 2
Views: 1125

Re: Skynet Firmware

MasterFX wrote:I'm using Skynet Firmware on my A8 without any problems. Since it is only a slightly modified Marlin Firmware there is no problem.
You don't have to change any parameters in your Profile which you have used with your stock firmware.

Thanks!
by smeek
Wed May 17, 2017 11:13 am
Forum: General Discussion and Tips
Topic: Sharing: Raise3D Pause Script
Replies: 8
Views: 5744

Re: Sharing: Raise3D Pause Script

Hello, pretty new to 3D printing but learning. Big fan of S3D so far. Can someone share a post script that would work for an Anet A8 for changing color filament. I found a couple examples but didn't work for me so probably for different firmware. I just want to pause the print after layer 4, move th...

Go to advanced search