+1
Thanks for the thread.
Search found 7 matches
- Mon Apr 22, 2019 8:58 am
- Forum: Feature Requests
- Topic: 3D Mouse
- Replies: 214
- Views: 228298
- Jump to post
- Mon Apr 22, 2019 8:45 am
- Forum: Feature Requests
- Topic: Cooling :: Blib fan to full power :: Avoid G4 P500
- Replies: 0
- Views: 1659
- Jump to post
Cooling :: Blib fan to full power :: Avoid G4 P500
Where: In all Versions I know -> within FFF Settings -> Cooling -> Fan Options There is this checkbox which label is "Blib fan to full power when increasing from idle" Why the option is needed: This option is ment to kickstart a fan to a spinning state when commanding low rotation speeds. ...
- Sat Dec 09, 2017 4:49 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Extrusion Speed vs. Print Speed
- Replies: 6
- Views: 17235
- Jump to post
Re: Extrusion Speed vs. Print Speed
+1 for the Thread. I would as well have a cap for extrusion volume / s Of course we could just calculate the flow according to speed. But a real software cap would be easier. Reasons: 1) Your material is heated up within your chamber. If you go to some extrusion-limit you would need to increase temp...
- Sun Sep 03, 2017 7:27 pm
- Forum: General Discussion and Tips
- Topic: pause / resume from the mcp, reading pause from fw..
- Replies: 3
- Views: 4133
- Jump to post
Re: pause / resume from the mcp, reading pause from fw..
Using Repetier-Server / -Host you just send commands like: start (for unexpected reboot -> stops all printing) RequestStop: RequestPause: RequestContinue: from the Firmware to the server/host using Logdata -> and it stops sending G-Code. Is this supported by Simplify3D too, today? The acutal use is ...
- Sun May 28, 2017 8:16 am
- Forum: General Discussion and Tips
- Topic: Walls that are more than 1 line thick
- Replies: 4
- Views: 2434
- Jump to post
Re: Walls that are more than 1 line thick
Hello!
For a better visibility:
Those are double line infills according to the link and approved "new feature" which should have been implemented in 2.2.
Where is this feature in Simplify3D?
Greetings!
For a better visibility:
Those are double line infills according to the link and approved "new feature" which should have been implemented in 2.2.
Where is this feature in Simplify3D?
Greetings!
- Fri May 26, 2017 4:00 pm
- Forum: General Discussion and Tips
- Topic: How to make a perfect bridge?
- Replies: 3
- Views: 2780
- Jump to post
Re: How to make a perfect bridge?
Yesterday i encountered this weired type of bridging: https://image.prntscr.com/image/993b59d0bc2d4da7b123e187b9175f11.png Explained: This is the first layer after Air and the Bridge is surrounded by something like U or |_|-form. Slic3r did correctly bridge the long way from cliff to cliff. But Simp...
- Fri May 26, 2017 12:20 pm
- Forum: General Discussion and Tips
- Topic: Walls that are more than 1 line thick
- Replies: 4
- Views: 2434
- Jump to post
Walls that are more than 1 line thick
There was this previous feature request about double-line walls for infill: https://forum.simplify3d.com/viewtopic.php?f=8&t=1405#p12770 JasonCS postet: "This feature was implemented in version 2.2" (This topic is locked and at least two people were not able to find the feature in Vers...
