Search found 7 matches
- Tue Jun 08, 2021 4:32 pm
- Forum: General Discussion and Tips
- Topic: Dead Project?
- Replies: 2
- Views: 3138
- Jump to post
Dead Project?
I'm wondering, it's been quite some time since 5.0 was announced. Is this now a dead project? Also, are there no more updates for 4.1? There is no date stamp on the release date, but this is becoming frustrating. I only use my s3d for viewing gcode produced by another slicer. I used to LOVE S3d and ...
- Sat Apr 06, 2019 10:55 pm
- Forum: Troubleshooting and Bug Reports
- Topic: Is there a way of changing the final surface pattern
- Replies: 2
- Views: 912
- Jump to post
Re: Is there a way of changing the final surface pattern
Howard, In your FFF settings, change your "External Infil Pattern" to Rectilinear. Then change your "External Infill Angle Offsets to 45° and -45° 
- Sat Apr 06, 2019 10:42 pm
- Forum: Feature Requests
- Topic: Makerbot Replicator+
- Replies: 0
- Views: 819
- Jump to post
Makerbot Replicator+
Please add full support for MakerBot Replicator+. I know that the 5th gen is VERY similar, but it is not the same. I have been hoping that you would add full support since this printer was purchased in 2016. Also, I noticed that after the last software update (4.1.2) circles are now printing oblong....
- Sat Apr 06, 2019 10:40 pm
- Forum: Feature Requests
- Topic: SpiderWeb infill
- Replies: 0
- Views: 716
- Jump to post
SpiderWeb infill
I print quite a lot of circular parts. I would like to minimize my infill, but maximize strength. Is it possible to add an infill that "radiates" from the center of a circular cutout/hollow and then also has cross infill on that? Think spiderweb-esque...
- Sat Feb 10, 2018 10:50 am
- Forum: Troubleshooting and Bug Reports
- Topic: Makerbot Replicator+ heat sap
- Replies: 2
- Views: 1208
- Jump to post
Re: Makerbot Replicator+ heat sap
Sorry it has been so long. Heat sap = a 20degree drop in the extruder. I have been searching for code to input in the gcode for the extruder to report back to the printer more often and have the printer adjust the temp as needed. (I am newer to 3d printing, but I have machining experience with gcode...
- Fri Jan 12, 2018 10:08 am
- Forum: Troubleshooting and Bug Reports
- Topic: Makerbot Replicator+ heat sap
- Replies: 2
- Views: 1208
- Jump to post
Makerbot Replicator+ heat sap
I have a Makerbot Replicator+. When I try to run a print that was generated with S3D, after about 15 minutes, the print stops and I get a heat sap error. When I print the same print using the makerbot software to generate g-code, There are no heat issues (just crappy prints!). There was a firmware u...
- Mon Nov 06, 2017 8:04 pm
- Forum: General Discussion and Tips
- Topic: Sticking filament to the build plate
- Replies: 0
- Views: 949
- Jump to post
Sticking filament to the build plate
So far I have been able to get PLA, ABS, and PETG all to stick to an unheated build plate by using plasti dip coating (I use the dip in a can vs the spray and just use $.30 paint brushes to apply). I was struggling to get prints to stick on this makerbot replicator+ unheated bed (and no good way to ...
