Search found 25 matches

Go to advanced search

by davorin
Sat Feb 02, 2019 6:04 am
Forum: General Discussion and Tips
Topic: 100% infill and solid outer fill printed separately
Replies: 4
Views: 419

100% infill and solid outer fill printed separately

Good morning

To increase the stiffness of some objects I want to print the infill also with 100%.

Is there a way that the code generated doesn't print both 100% fill separately?


thanks in advance
richard
by davorin
Sat Jan 26, 2019 7:44 am
Forum: General Discussion and Tips
Topic: CR-10S homing position
Replies: 0
Views: 175

CR-10S homing position

Good afternoon (o; This might be out of topic as it has nothing to do with Simplify3d, but I just don't wanted to subscribe to another forum ;-) Currently I use the Ender-3 printer with a FIlaPrint base which I am very happy with it... and as the license model allows to be used on two computers I ha...
by davorin
Wed Jan 23, 2019 4:43 am
Forum: Troubleshooting and Bug Reports
Topic: Support problem
Replies: 6
Views: 343

Re: Support problem

Hmm..seems this model is unprintable....tried now with raft and support....but it generates very long bridging which can't be printed...
by davorin
Sun Jan 20, 2019 8:47 am
Forum: Troubleshooting and Bug Reports
Topic: [Solved] Leaves thick strings and lumps during printing
Replies: 11
Views: 574

Re: [Solved] Leaves thick strings and lumps during printing

Let the printer work over night...seems I haven't tightened enough the PTFE tube in the heatsink...so it eventually popped out....cleaned everything inserted a new nozzle...and forgot to tighten the nozzle again after heating up.....so starting again from beginning (o; If I want to replace the nozzl...
by davorin
Thu Jan 17, 2019 8:48 am
Forum: Troubleshooting and Bug Reports
Topic: Support problem
Replies: 6
Views: 343

Re: Support problem

Yes...there are loads of settings (o;

Here is the factory file...
by davorin
Thu Jan 17, 2019 5:09 am
Forum: Troubleshooting and Bug Reports
Topic: Support problem
Replies: 6
Views: 343

Support problem

Good morning (o; Another support I have with a specific model...though I don't know how to solve the problem... The model starts very thin and gets thicker at layer 6....though only little support is generated at the corners: This is at layer 5 where only few support is generated at the inside corne...
by davorin
Tue Jan 15, 2019 11:51 am
Forum: Troubleshooting and Bug Reports
Topic: Solid layer same direction as support
Replies: 7
Views: 234

Re: Solid layer same direction as support

I used this from thingiverse:

https://www.thingiverse.com/thing:3042208

And within the archive I used the Ender3_Fan_Cover_Side.stl file...

The screenshots were taken at 0.2mm layer, so layer 62 - 64 is interesting....
by davorin
Tue Jan 15, 2019 7:06 am
Forum: Troubleshooting and Bug Reports
Topic: Solid layer same direction as support
Replies: 7
Views: 234

Re: Solid layer same direction as support

No it is set to 0...but if I set to one layer it doesn't change anything...first solid layer is still horizontal....and the next two solid layers are +/- 45 degrees...
by davorin
Tue Jan 15, 2019 5:42 am
Forum: Troubleshooting and Bug Reports
Topic: Solid layer same direction as support
Replies: 7
Views: 234

Re: Solid layer same direction as support

Sorry for confusing screenshots (o;

I have the default settings of +/- 45 degrees for inner and outer infill....
So what defines that it does a horizontal hatch at the first outer layer?
The next solid layer is then done with 1/- 45 degrees...
by davorin
Tue Jan 15, 2019 4:08 am
Forum: Troubleshooting and Bug Reports
Topic: Solid layer same direction as support
Replies: 7
Views: 234

Solid layer same direction as support

Good morning... Recently I printed a fan cover for my Ender-3 printer...where I discovered when using the automatic support generation it leaves out one layer totally...and then makes a solid hatch, but in the same horizontal direction as the support layer before.... Should a solid layer not always ...

Go to advanced search