Search found 21 matches

Go to advanced search

by 24c
Wed Feb 21, 2018 3:43 am
Forum: Feature Requests
Topic: Feature Request - Custom Command Panel
Replies: 0
Views: 199

Feature Request - Custom Command Panel

I've asked about this before in emails to Support, with no response, so hence this post. Why is the Custom Commands Panel only about 3 customisable macros, I could use a lot more, and this feature is enabled in Printer Host, Matter Control & Print Run too. Simplify3D-MachineControlPanel-CustomComman...
by 24c
Sat Feb 17, 2018 6:13 am
Forum: Feature Requests
Topic: a couple of ideas for dual extruder printing
Replies: 3
Views: 558

Re: a couple of ideas for dual extruder printing

...which leaves the idle nozzle at temperature for the entire layer even if it is only used at the end, would it be possible to put in a "startup" routine for a nozzle that only starts bringing it up to temp a certain amount of time (estimated from printing speed) before it starts being used instea...
by 24c
Sat Feb 17, 2018 4:45 am
Forum: General Discussion and Tips
Topic: Dual extrusion with multiple groups?
Replies: 4
Views: 1491

Re: Dual extrusion with multiple groups?

IMHO Having this feature checked by default is the worst aspect of the software..... It just doesn't make sense. I pull my hair out, every. single. time. that-checkbox.png LMAO, I had exactly the same issue, and wondered why too, but you can get around it... by using this, and not having to re-impo...
by 24c
Wed Feb 14, 2018 5:53 pm
Forum: Troubleshooting and Bug Reports
Topic: Separate support processes for dual extruder
Replies: 9
Views: 1110

Re: Separate support processes for dual extruder

If I wanted to figure out how to write a tool change script that made a global speed change I guess that might somehow work, but I don't write G Code, that's why I purchased Simplify3D.... I bought Simplify3D for my RepRap dual extrusion printer, and I had to learn how to write GCode to get Simplif...
by 24c
Tue Feb 13, 2018 12:13 pm
Forum: Troubleshooting and Bug Reports
Topic: Separate support processes for dual extruder
Replies: 9
Views: 1110

Re: Separate support processes for dual extruder

I'm new to this, but surely the heads are related to a tool change, so can't you make a new condition when the new tool is selected either as a tool change script or a post process, that slows the print speed down globally? Simplistically, I am assuming you can do this with a GCode routine with your...
by 24c
Mon Feb 05, 2018 6:32 pm
Forum: Troubleshooting and Bug Reports
Topic: Temperature Setpoints
Replies: 1
Views: 294

Re: Temperature Setpoints

Solved, I just deleted them all, after saving one. :)
Then I checked the .frm and edited the FFF profile by hand and re-imported them both, and problem solved, so not sure why it was happening, having found the affected area of code, but it's history now.
by 24c
Mon Feb 05, 2018 1:36 pm
Forum: Troubleshooting and Bug Reports
Topic: Postprocessing command does not work
Replies: 5
Views: 1388

Re: Postprocessing command does not work

Is it because you are adding a T0, as I'm sure if you do {TOOL0REPLACE "G1 E-4.0000 F6000\n" "T3\n G10\n"} this will work Another trick I learnt, if you want to invoke an event before a Tool Change in a Tool Change Script add a value like this "XXXX" XXXX G1 B0 T[new_tool] and then use a post proces...
by 24c
Mon Feb 05, 2018 11:57 am
Forum: Troubleshooting and Bug Reports
Topic: Temperature Setpoints
Replies: 1
Views: 294

Temperature Setpoints

I am trying to understand why if I create a process, select a profile with known temperature setpoints for layer 1 & 2, why selecting another extruder type say Extruder 1, Extruder 2 or All extruders, seems to corrupt the profiles temperature setpoints, and mine keeps defaulting back to 190ºC, when ...
by 24c
Fri Feb 02, 2018 6:33 am
Forum: General Discussion and Tips
Topic: CEL Robox Support
Replies: 15
Views: 5707

Re: CEL Robox Support

OK, so three attachments are the limit, so here's the Profile and .frm file for a QuickFill equipped Robox
by 24c
Fri Feb 02, 2018 6:29 am
Forum: General Discussion and Tips
Topic: CEL Robox Support
Replies: 15
Views: 5707

Re: CEL Robox Support

OK, so I've corrected a few things, and done away with the Simplify3D Tool Change Script, and added a simplistic one I used in the DM profile (I will revisit this sometime, once I have uncooked the DM head..hmmm the joys of trying to do something different). I have tested it so far, and it is workin...

Go to advanced search