Search found 13 matches

Go to advanced search

by DotScott1
Wed Jun 26, 2019 11:13 am
Forum: General Discussion and Tips
Topic: Volcano 0.8mm Nozzle on a CR-10 - Settings?
Replies: 5
Views: 375

Re: Volcano 0.8mm Nozzle on a CR-10 - Settings?

Hi DotScott1, I've got the exactly same issue using the volcano on a very expensive (>40K) printer. I've even dropped down to a 0.4 nozzle with similar results, better but no where near as good as my $500 CR-10s. I'm just about to post a Marvin in the hope someone might see something I could do to ...
by DotScott1
Tue Jun 25, 2019 5:48 pm
Forum: General Discussion and Tips
Topic: Volcano 0.8mm Nozzle on a CR-10 - Settings?
Replies: 5
Views: 375

Volcano 0.8mm Nozzle on a CR-10 - Settings?

Alright so... it's been a year or two since I've asked and I STILL have not perfected settings for my 0.8mm volcano nozzle/hot end on my CR-10S 400... They still just don't come out very clean. Either the walls look great but the tops and bottoms look bad OR the tops and bottoms look good and the wa...
by DotScott1
Thu Dec 13, 2018 12:08 pm
Forum: General Discussion and Tips
Topic: Pause at Height (NOT LAYER)?
Replies: 12
Views: 1494

Re: Pause at Height (NOT LAYER)?

Also I forgot to post my setup:

Octoprint connected to Creality CR-10S 400 printer.
by DotScott1
Thu Dec 13, 2018 12:08 pm
Forum: General Discussion and Tips
Topic: Pause at Height (NOT LAYER)?
Replies: 12
Views: 1494

Re: Pause at Height (NOT LAYER)?

HA! No kidding!... this was just fixed with the latest update (4.1.1)!! WOO! Wow I just downloaded the latest software today and this problem is just... gone. Everything works perfectly now because it counts the first layer of ALL objects on the bed as layer one (instead of layers 1, 2, 3, etc). Aa...
by DotScott1
Wed Dec 12, 2018 6:22 pm
Forum: General Discussion and Tips
Topic: Pause at Height (NOT LAYER)?
Replies: 12
Views: 1494

Re: Pause at Height (NOT LAYER)?

HA! No kidding!... this was just fixed with the latest update (4.1.1)!! WOO! Wow I just downloaded the latest software today and this problem is just... gone. Everything works perfectly now because it counts the first layer of ALL objects on the bed as layer one (instead of layers 1, 2, 3, etc). Aah...
by DotScott1
Tue Dec 11, 2018 4:22 pm
Forum: General Discussion and Tips
Topic: Pause at Height (NOT LAYER)?
Replies: 12
Views: 1494

Re: Pause at Height (NOT LAYER)?

I personally would alter the Gcode at the given layer (height) you want to stop at then place the command to pause, that is what I do, from your example are you creating a script to do this,, if so I think that's too complicated for me.. and I would do two prints. Well, that's basically what this s...
by DotScott1
Tue Dec 11, 2018 12:38 pm
Forum: General Discussion and Tips
Topic: Pause at Height (NOT LAYER)?
Replies: 12
Views: 1494

Re: Pause at Height (NOT LAYER)?

Anything? ... :(
by DotScott1
Fri Dec 07, 2018 1:38 pm
Forum: General Discussion and Tips
Topic: Pause at Height (NOT LAYER)?
Replies: 12
Views: 1494

Pause at Height (NOT LAYER)?

Hello, So I've been searching around and so far, all I can seem to find is a commend (below) for pausing the print at a certain LAYER, but I have not seen a command to pause the print at a certain HEIGHT. Is this possible? Here's what I have to pause at a certain LAYER: {REPLACE "\n; layer 22, Z = "...
by DotScott1
Fri Aug 31, 2018 11:32 am
Forum: General Discussion and Tips
Topic: Lost all S3D Profiles :( Can I Recover one from a Gcode File?
Replies: 3
Views: 662

Re: Lost all S3D Profiles :( Can I Recover one from a Gcode File?

dkightley wrote:
Thu Aug 30, 2018 12:42 pm
Here's your profile. I loaded it from your gcode file....and then saved it:
YOU. ARE. MY. HERO!! Thank you so much!!
by DotScott1
Thu Aug 30, 2018 9:40 am
Forum: General Discussion and Tips
Topic: Lost all S3D Profiles :( Can I Recover one from a Gcode File?
Replies: 3
Views: 662

Re: Lost all S3D Profiles :( Can I Recover one from a Gcode File?

Well I found the start code in notepad (in the gcode file) so... thank god for that! Looks like all the settings are in this file, will just take a while to transfer them all over. Wish I could get the import fff profile from gcode to work.

Go to advanced search