Search found 23 matches

Go to advanced search

by nfol
Sat Jun 15, 2019 5:17 am
Forum: Troubleshooting and Bug Reports
Topic: Connection error
Replies: 12
Views: 314

Re: Connection error

@S3D-Jake: I now allowed simplify3D.exe in Windows Firewall. Unfortunately this does not help, even I at the same time switch off my other firewall program. I do not understand why S3D is so complicated on this point, when I have several other programs that makes connections on the net without troub...
by nfol
Sat Jun 15, 2019 4:21 am
Forum: Troubleshooting and Bug Reports
Topic: Connection error
Replies: 12
Views: 314

Re: Connection error

@S3D-Jake

Thank you. I will look into that.
by nfol
Sat Jun 15, 2019 4:19 am
Forum: Troubleshooting and Bug Reports
Topic: Connection error
Replies: 12
Views: 314

Re: Connection error

@graybeard:

Would you be so kind as to explain a little deeper? What has firmware configuration to do with connection to the net?

Best regards,
Niels
by nfol
Thu Jun 13, 2019 7:14 am
Forum: Troubleshooting and Bug Reports
Topic: Connection error
Replies: 12
Views: 314

Re: Connection error

ratak477: > Have you found a solution yet? Unfortunately not. S3D support says that the message "Connection error" must be a Firewall issue, even it doesn't help to switch off my firewall program. Will someone be so kind as to tell me if there is an additional firewall in Win10 itself? And how to wh...
by nfol
Wed May 29, 2019 1:13 pm
Forum: Troubleshooting and Bug Reports
Topic: Connection error
Replies: 12
Views: 314

Re: Connection error

> You might click on the network settings button and see what is listed there. I don't thing this can be otherwise. Screen clip attached. > Also try going to the help menu and selecting to do a restore or return to factory settings - don't remember exactly what it is called. It is called "Reset All ...
by nfol
Wed May 29, 2019 3:42 am
Forum: Troubleshooting and Bug Reports
Topic: Connection error
Replies: 12
Views: 314

Connection error

When I click "Check for updates" or "Configuration assistant", I keep getting the message "Connection error". Support suggests that it could be due to my firewall. However, it does not help to switch off the firewall. My username and password is fully updated. I have no problem logging into my accou...
by nfol
Fri May 24, 2019 5:30 am
Forum: Troubleshooting and Bug Reports
Topic: Support area wwoun't be neat
Replies: 5
Views: 127

Re: Support area wwoun't be neat

Other good points. Thank you for your help.

I wonder if S3D could have a go-away-and-wait function, so that you do not have to print two objects to get sufficient breaks between layers.
by nfol
Thu May 23, 2019 12:38 pm
Forum: Troubleshooting and Bug Reports
Topic: Support area wwoun't be neat
Replies: 5
Views: 127

Re: Support area wwoun't be neat

Thank you for your reply. I tried to decrease the temperature from 195 to 190 and to 185. No change. Then I added 4 layers dense support 100%. No significant change. At temp 200 and printing two objects, the result was a bit better (at the filleted edge), but still not good enough. Regarding dense s...
by nfol
Wed May 22, 2019 9:55 am
Forum: Troubleshooting and Bug Reports
Topic: Support area wwoun't be neat
Replies: 5
Views: 127

Re: Support area wwoun't be neat

Here is the picture.
by nfol
Wed May 22, 2019 9:53 am
Forum: Troubleshooting and Bug Reports
Topic: Support area wwoun't be neat
Replies: 5
Views: 127

Support area wwoun't be neat

As can be seen on the picture, the lower site of this curved model is horrible as is the filleted edge at the same level. I tried many different settings without succes. The test model here is part of a bigger model. That's why it is oriented as is.) I very much appreciate any help. Best regards, Ni...

Go to advanced search