Search found 7 matches

Go to advanced search

by UnRealWoody
Wed Nov 04, 2020 10:09 pm
Forum: General Discussion and Tips
Topic: Flashforge Creator 3
Replies: 5
Views: 796

Re: Flashforge Creator 3

Hi, I just bought S3D. It's really not practical you cannot send .g file to Creator 3 like flashprint can. So that's a minus. But I can use S3D to make .g and send .g with flashprint to printer. My question is though, are there any good profiles for printing for S3D with flashforge? There's a gazil...
by UnRealWoody
Sun Nov 01, 2020 3:23 pm
Forum: General Discussion and Tips
Topic: Flashforge Creator 3
Replies: 5
Views: 796

Re: Flashforge Creator 3

NO Flashforge Creator 3 is only connectable via Ethernet or Wify And this software is not able to communicate with it ! You need to save on a USB stick and load again in printer. Not easy I would not recommend S3D for a creator 3 I highly disagree. Both S3D and the creator 3 are made very easy to s...
by UnRealWoody
Sun Nov 01, 2020 3:20 pm
Forum: General Discussion and Tips
Topic: Flashforge Creator 3 and Simplify 3D New User?
Replies: 3
Views: 761

Re: Flashforge Creator 3 and Simplify 3D New User?

S3D does work for the Creator 3. I havent had many issues. I did run into an issue with S3D that the left and right nozzle alignment was incorrect, but after adjusting the tool 1 on the x axis by -1.78 mm, i did have this resolved. Also, an additional issue i am noticing is that if the print is paus...
by UnRealWoody
Sun Nov 01, 2020 2:16 pm
Forum: General Discussion and Tips
Topic: Flashforge Creator 3 unalligned on x-axis after pausing print
Replies: 0
Views: 163

Flashforge Creator 3 unalligned on x-axis after pausing print

Has anybody figured out yet what to adjust to avoid the print not being alligned after the print got paused?
I am not sure what to adjust for this.

BTW: This offset is 0.85 mm. This offset only happens when G code was made with S3D, this does not happen if using other slicers like Flashprint.
by UnRealWoody
Tue Nov 26, 2019 9:34 pm
Forum: Feature Requests
Topic: Flashforge Creator3
Replies: 40
Views: 43952

Re: Flashforge Creator3

Tried the fff config however it appears (at least for me) the duplicate printing is trending to the left. So what happens is that either though it appears ok in flashprint the left hand side of the right extruder print, prints over the top of the right hand side of the left extruder print. Can you ...
by UnRealWoody
Tue Nov 26, 2019 9:31 pm
Forum: Feature Requests
Topic: Flashforge Creator3
Replies: 40
Views: 43952

Re: Flashforge Creator3

I am considering adding this printer as another production printer. What are your opinions on it so far? Thanks. It includes some annoying safety features that would cause me to not recommend it for a production environment printer. Most frustrating of them would be the fact that back to back print...
by UnRealWoody
Mon Nov 11, 2019 3:33 pm
Forum: Feature Requests
Topic: Smarter Raft and Support
Replies: 2
Views: 1383

Smarter Raft and Support

At this moment, if you have supports added to a piece and a raft, the supports are also lifted of the raft. It would be very beneficial for me to be able to lift the piece off the raft, but have the supports really stuck to the raft. This is helpful for printing small detailed pieces, with or withou...

Go to advanced search