Search found 16 matches

Go to advanced search

by KarlW1000
Fri Feb 02, 2024 1:57 pm
Forum: General Discussion and Tips
Topic: Accessory Controls
Replies: 0
Views: 896
 
Jump to post

Accessory Controls

Version 5, On the Accessory Controls in the Machine Control Panel, does anyone know if there's way to set defaults for the bed and Primary extruder temperatures?
Thanks
Karl
by KarlW1000
Fri Feb 02, 2024 11:05 am
Forum: Troubleshooting and Bug Reports
Topic: E-Stop and Pause Not Working
Replies: 11
Views: 9853
 
Jump to post

Re: E-Stop and Pause Not Working

Bought it in April of 2014.
According to this site:

"https://makergear.zendesk.com/hc/en-us/ ... D-Printers"

the revision is B.1
by KarlW1000
Thu Feb 01, 2024 11:47 am
Forum: Troubleshooting and Bug Reports
Topic: E-Stop and Pause Not Working
Replies: 11
Views: 9853
 
Jump to post

Re: E-Stop and Pause Not Working

Manually sending M112 from either version does nothing. Re-downloaded the most current Firmware for my machine from Makergear and installed Same results, M112 does nothing. Output when connecting to the printer: Attempting connection at \\.\COM3... READ: start READ: echo:Marlin: 1.0.0 RC2 for MakerG...
by KarlW1000
Thu Feb 01, 2024 9:24 am
Forum: Troubleshooting and Bug Reports
Topic: E-Stop and Pause Not Working
Replies: 11
Views: 9853
 
Jump to post

Re: E-Stop and Pause Not Working

Jason, Just to be clear, when I say stopped below, I mean the motors are disabled, bed heater is turned off, extrude heater is turned off, program execution is halted, everything is reset as if the printer was just connected to the computer. I am running Simplify3D Versions 4.1.2 and 5.1.2 on the sa...
by KarlW1000
Tue Jan 30, 2024 8:09 pm
Forum: Troubleshooting and Bug Reports
Topic: E-Stop and Pause Not Working
Replies: 11
Views: 9853
 
Jump to post

Re: E-Stop and Pause Not Working

Jason, Any word from the programmers about getting the E-Stop to work as in version 4.1.2? Pressing the E-stop button or sending the M112 command will NOT stop the machine. The movement will stop after about 8 more lines of code are executed but the bed heater and motors are never shut off. Currentl...
by KarlW1000
Mon Dec 04, 2023 7:44 am
Forum: Troubleshooting and Bug Reports
Topic: E-Stop and Pause Not Working
Replies: 11
Views: 9853
 
Jump to post

Re: E-Stop and Pause Not Working

Jason,
Since the OP did not reply, do you know if anything has been found about this. I can't imagine the OP and myself are the only 2 that have experienced this behavior. It would be nice if the E-Stop worked as in version 4 and stopped the machine immediately.
Karl
by KarlW1000
Mon Dec 04, 2023 7:38 am
Forum: General Discussion and Tips
Topic: Version 6 ??
Replies: 3
Views: 9305
 
Jump to post

Version 6 ??

Jason, I have realized that getting the check boxes back that we had in version 4 will not happen. After reading all the different comments about the boxes, we will probably not see anything until the next paid version comes out because the check boxes will act slightly different and classified as a...
by KarlW1000
Tue Jul 11, 2023 6:04 am
Forum: Feature Requests
Topic: Begin printing does not remember the selected machine
Replies: 2
Views: 900
 
Jump to post

Re: Begin printing does not remember the selected machine

Always having to select which printer to use is unnecessary when you only have one printer. A checkbox or some way to stop asking would be a welcome addition.
by KarlW1000
Sun Jul 02, 2023 7:43 pm
Forum: Troubleshooting and Bug Reports
Topic: No checkmark to hide the objects in V5
Replies: 24
Views: 12281
 
Jump to post

Re: No checkmark to hide the objects in V5

+1

This is very helpful when multiple models are loaded
by KarlW1000
Sun Jul 02, 2023 7:33 pm
Forum: Troubleshooting and Bug Reports
Topic: E-Stop and Pause Not Working
Replies: 11
Views: 9853
 
Jump to post

Re: E-Stop and Pause Not Working

I have the same When using Simplify3D V5.1 I have the same behavior. When I press the E-Stop, approx. 8 more lines of code will be executed before the x, y and z are halted and the nozzle stops extruding plastic. The axis motors are still enabled and holding position and the heaters for the bed and ...

Go to advanced search