Search found 17 matches

Go to advanced search

by Zeeflyboy
Wed Feb 26, 2014 4:38 pm
Forum: Feature Requests
Topic: Feature Request: First Layer Thickness
Replies: 7
Views: 3772

Re: Feature Request: First Layer Thickness

it's also limited to 199%

I think the slic3r approach of allowing you to simply type in a first layer height is more intuitive.
by Zeeflyboy
Sun Jan 26, 2014 5:45 pm
Forum: General Discussion and Tips
Topic: Run time estimate way off
Replies: 3
Views: 1570

Re: Run time estimate way off

I think it is not possible to have a completely accurate "estimate". Your firmware settings affect how acceleration is handled and that information the slicer does not know, it can only guess. The material usage on the other hand should be quite close, if it is way off you would have serious over o...
by Zeeflyboy
Sun Jan 26, 2014 5:34 pm
Forum: General Discussion and Tips
Topic: Panning in Creator ssoftware on mac air
Replies: 1
Views: 708

Re: Panning in Creator ssoftware on mac air

I have right click as a two finger click on the touchpad and that works fine on my macbook pro - just push down the pad with two fingers and then move them around to pan.
by Zeeflyboy
Sun Jan 26, 2014 5:12 am
Forum: Feature Requests
Topic: [ADDED] independent axis scaling
Replies: 4
Views: 1895

[ADDED] independent axis scaling

Unless I missed it, currently it is only possible to scale the model globally with a fixed aspect ratio. Can we get the option to scale each axis independently? When adjusting for ABS shrinkage for example I find 1% works well in X and Y but isn't required in Z... in some tight tolerance parts the f...
by Zeeflyboy
Sat Jan 25, 2014 3:33 pm
Forum: Feature Requests
Topic: Feature Request Branching support scaffold
Replies: 4
Views: 2537

Re: Feature Request Branching support scaffold

agreed! The meshmixer supports are great (although I edit the parameters and make them thicker, on supports where they start on the model rather than the base they also need more than one contact point to be reliable, but you can add these manually. Haven't seen the adobe ones. To have a similar nat...
by Zeeflyboy
Sat Jan 11, 2014 9:09 am
Forum: General Discussion and Tips
Topic: Feature request
Replies: 17
Views: 4372

Re: Feature request

I know it's a slightly old thread, but I would like to put in a request for honeycomb infill too - I've been playing with slic3r a lot lately and find honeycomb better for ABS.
by Zeeflyboy
Sun Dec 22, 2013 2:20 pm
Forum: General Discussion and Tips
Topic: 2.0.1 update osx - any version notes?
Replies: 7
Views: 1902

Re: 2.0.1 update osx - any version notes?

seems layer heights have gone a bit bizarre (at least on my m2 profile) - is this in accordance with actual steps?

edit - nevermind was just something weird, reset the profile and it's back to normal (albeit with more decimal places than I remember lol)
by Zeeflyboy
Fri Dec 06, 2013 5:27 pm
Forum: General Discussion and Tips
Topic: Found 2.0.0 in the downloads last night
Replies: 21
Views: 5155

Re: Found 2.0.0 in the downloads last night

great, just downloaded it - thanks for the heads up.

Any reason why the Creator software is fuzzy and low res on my new retina display MBP 13"? seems to be the only program I have affected by it - the buttons and text are all a bit blurry and low res looking.
by Zeeflyboy
Mon Nov 11, 2013 7:39 am
Forum: Troubleshooting and Bug Reports
Topic: PLA High quality profile doesn't "cap" parts
Replies: 23
Views: 11634

Re: PLA High quality profile doesn't "cap" parts

The root cause of the problem I was seeing is how the slicer resolves the issue of the what to do with the infill when the feature thickness is less than the thickness dictated by the number of perimeter shells. For example, let's say I'm calling for 3 perimeter shells. Based on my nozzle and filim...
by Zeeflyboy
Thu Oct 10, 2013 7:56 am
Forum: Troubleshooting and Bug Reports
Topic: weird feeding problem with windows version
Replies: 2
Views: 1240

Re: weird feeding problem with windows version

I think I may have deleted the files to prevent me from selecting the wrong ones...

I'll generate some more today and post them up when I get a chance.

Go to advanced search