Search found 721 matches: pause

Searched query: pause

Go to advanced search

by S3D-Jake
Thu Jan 21, 2021 2:48 pm
Forum: General Discussion and Tips
Topic: Post processing GCODE help ?
Replies: 1
Views: 53

Re: Post processing GCODE help ?

... This all sounds great. retractions and priming inserted with a REPLACE command will not have knowledge of the current E value leading up to your pause command. So if you include adjustments to the E value I recommend that they be performed with "Relative Extrusions" enabled and then disabled ...
by ve6btc
Wed Jan 20, 2021 4:31 pm
Forum: General Discussion and Tips
Topic: Post processing GCODE help ?
Replies: 1
Views: 53

Post processing GCODE help ?

Hello fellow makers so was just looking for a wee bit of help I’m printing a item that I am inserting a magnet into that’s no problem I got the pause at layer height and move to x 0 y 0 and beep to alert it’s waiting But in addition to that I’d like to have it turn the extruder off so I don’t ...
by benfinklea
Sat Nov 28, 2020 9:21 am
Forum: Feature Requests
Topic: Programmed Pause
Replies: 20
Views: 12141

Re: Programmed Pause

{REPLACE "; layer 3" ";move away and pause \nG1 Z10 F1800 \nG1 Y10 X10 F3000 \nM0 \nG28 X \nG92 E0 \nG1 E-1.7500 F900 \n; layer 3"} A slight adjustment to Broncosis' amazing bit of code: {REPLACE "; layer 3," ";move away and pause \nG1 Z10 ...
by parallyze
Mon Nov 02, 2020 2:05 pm
Forum: Troubleshooting and Bug Reports
Topic: Printer stops for 4 seconds at the start and at the end of every line
Replies: 1
Views: 194

Re: Printer stops for 4 seconds at the start and at the end of every line

... would be helpful to check the settings. Or the same segments from a gcode file created with S3D vs. Cura. If other slicers gcode doesn't cause the pause while printing it should be easy to find. Just a guess, but is "Relative extrusion distances" selected? If not there might be a G92 E0 following ...
by parallyze
Wed Oct 14, 2020 4:04 pm
Forum: Troubleshooting and Bug Reports
Topic: Blobs on seam
Replies: 3
Views: 344

Re: Blobs on seam

... "Only retract when crossing open spaces" on the "Advanced" tab might have an impact here. Would be good to see settings/gcode because of that pause/delay you mention...
by S3D-Jake
Mon Oct 12, 2020 3:13 pm
Forum: Troubleshooting and Bug Reports
Topic: Using Pause on Control Interface
Replies: 1
Views: 300

Re: Using Pause on Control Interface

Can you clarify if you're having issues with the Simplify3D machine control panel's pause function or that of the Ender 5 Pro's own printer controls?
by Crazychefruss
Sun Oct 11, 2020 10:53 am
Forum: Troubleshooting and Bug Reports
Topic: Using Pause on Control Interface
Replies: 1
Views: 300

Using Pause on Control Interface

... Pro. I understand how to use S3D to stop at a desired height to change filament colours or for some other task, however I am looking to be able to pause "on the fly" as it were as If suddenly i realise my filament is going to run out or I just want to for some reason. Having the print head stop ...
by swiftninja
Tue Oct 06, 2020 6:40 pm
Forum: Troubleshooting and Bug Reports
Topic: Filament Runout Sensor
Replies: 2
Views: 1826

Re: Filament Runout Sensor

... is used for printing (as opposed to something like SD Card or USB Printing), Marlin sends a command back to the host to ask the HOST software to pause the print. So, yes - the filament runout bits exist and are handled in Marlin - 100% when using SD/Storage printing, but only the detection is ...
by parallyze
Thu Sep 24, 2020 7:30 pm
Forum: Troubleshooting and Bug Reports
Topic: Scars/Scuffs on surface of prints?
Replies: 11
Views: 1746

Re: Scars/Scuffs on surface of prints?

... layer from the second gcode file. This will result in massive overextrusion. If I may suggest something: Check out if your printer does support a pause/change filament command, like M600. As far as I can tell your Mega X is based on Marlin firmware, so it should support this command: https://marlinfw.org/docs/gcode/M600.html ...
by swimmerhair
Tue Sep 22, 2020 7:50 pm
Forum: Troubleshooting and Bug Reports
Topic: Trying to captivate some hardware with XYZ DaVinci Duo 2.0 but running into crashing issues
Replies: 1
Views: 267

Trying to captivate some hardware with XYZ DaVinci Duo 2.0 but running into crashing issues

Hey Everyone, Like the title suggests I am trying to captivate some hardware (nuts) in my print. I could not get the pause script to work so instead I did two prints. The first print, I printed up to layer X and stopped. I inserted the hardware and then ran another print where is ...

Go to advanced search